Kreg Owners' Community

I recently purchased a Kreg Precision Miter Gauge System for my table saw. I assembled everything and calibrated it per the instructions. It has been working great doing crosscuts. I had my first opportunity to use it to do miter cuts since I'm making a picture frame.

Each outside edge of the frame is 19 1/4" long. So, I rough cut 4 pieces 21" long. I then set my Kreg Miter Gauge to cut the first 45 degree angle. I placed the outside edge of a frame piece against the gauge fence and made the first angled cut. Then to cut the 45 degree cut on the other end I flipped the piece, keeping the outside edge against the gauge fence. Then using the scale on the top of the miter gauge I set the Swing Stop to 19 1/4". I then cut the second 45 degree angle.

Here is the problem - after cutting both ends of the piece, when I measured the outside edge of the frame it was 9/16" too long!

So, did I do something wrong or can you not use the scale on the guide when cutting angles?

Views: 488

Reply to This

Replies to This Discussion

I would say your setup for the tape measure is 9\16 off check from blade to 19 1/4. Good thing your not to short.

My first guess is that the flip stop isn't wide enough to properly register the stock. Did it stop at the extreme end of the point, or somewhere down on the angle?

Second guess would be that you set the stop with the guage at the 45 position to the closest point on the blade. Set the flip with the guage in the 90 position.

If you set the gauge relative to the blade at 90, then move it to 45, the end of the gauge is going to move further away from the blade as it pivots resulting in a longer than desired cut.
Doh... That's a certifiable "what was I thinkin" Thanks for the catch Bob.

Bob S said:
If you set the gauge relative to the blade at 90, then move it to 45, the end of the gauge is going to move further away from the blade as it pivots resulting in a longer than desired cut.
In other words, each time I want to make an angled cut I have to re-calibrate the scale, then when I'm done I need to again re-calibrate the scale back to 90 degrees?

Hi chuck!

The answer to your question is yes. After spending a few years in a machine shop, and many years remodeling houses, I've found that a good rule of thumb is if you move anything, recheck for accuracy. Unfortunately, pretty much all of my mistakes were caused by my lack of diligence. You are lucky, though, that you ended up long. My rather large pile of "on hand stock" is a result of my luck going the other way. Be patient...take your time...and above all, keep trying. Making stuff is very self satisfying. It's the pros that make it look easy. They weren't always pro, either, ya know.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

Videos

  • Add Videos
  • View All

Forum

Untitled

No Description

Started by Joe in Beginners' Zone 20 hours ago.

First time I really had a need for the ACS miter guide.

I've been using my Adaptive Cutting System table for a few years now, and it's been really solid. This past week was the first time I ever needed to use the miter guide though.I was rebuilding some shelving in a tiny closet and I discovered the…Continue

Tags: ACS

Started by Adam in General Woodworking May 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_