Kreg Owners' Community

can anyone tell me how to use the portable base? What tdo the markings on it mean as to setting depth ? thank you. 

Views: 1028

Reply to This

Replies to This Discussion

Hi Joe;

I not sure what portable base you are asking about but most marking on the bases are for the thickness of the wood to set the base the right distance from the joint, to set the depth or stop collar on your drill is done with a different guide sometimes in the case like on the R3 jig.

 

Hope this helps you maybe someone else can help more.

Hi Ray, 

I am talking about the K3 which has a poratble base with a lip on the end of it that hangs over the end the piece being drilled. The drill block slides into it. On the side of the portable base are lines with markings at 1/2, 3/4 , etc.

I know   how to use the drill block by itself because I've use the little single hole ones before,   but I don't see any explanation how to set it if it is inserted in the portable base. 

Thank you for your interest and help with my question.

Joe

Hello Joe,

Here is a Kreg Joinery Quick-Start Guide with complete instructions on proper setup and use: http://www.kregtool.com/prodimages/kregjigquickstarguide_0.pdf.

For the strongest joint possible, you need to properly position the location of your pocket holes according to your material thickness. To do this, start with your K3 Drill Guide situated in your Portable Base. Then, raise or lower the Drill Guide's height using the positioning pin on your Portable Base. Simply loosen the pin and raise the Drill Guide until the correct mark is showing just above the jig body, and then re-tighten the pin. The correct mark is based on the thickness of material you are working with. See an example below set for 3/4" material:
If this still does not make sense, please contact the Kreg Customer Service Team at 800-447-8638; they will be happy to walk you through the steps.

Have a great day!
KregRep

Thanks, now why couldn't i find that in my book? It just said see online for proper use instructions. The instructions you sent explain it. Just one more question though. What do the marks on the side of the portable base itself represent ?  

Joe, the markings on the portable base itself are what you use to set your depth collar. So, for example, if you are working with 3/4"-thick wood, set your depth collar by aligning it with the 3/4" marking and then tightening the stop collar with the included Allen wrench.

Thank you for bringing this issue to our attention. I just examined the instructions that comes with the Portable Base and you are right; there are no instructions on what its markings are for. We will update the instructions soon.

Thanks again!
KregRep

FYI, as of May, 2016 your instructions still have no information as to how to use the marks found on the portable base. I am unclear from this thread how to use them, and after speaking with one of your representatives, I still don't know. Maybe I am not smart enough for this tool.

Dear Joe,

The markings you are referring to on the Portable Base allow you to set your depth collars setting.  Set the drill guide block at your correct setting in the portable base, for instance say you have it at the 3/4" mark like the picture posted by KregRep shows. 

Loosen the depth collar on your drill bit and slide the drill bit through one of the holes on the drill guide block.  Just like you do when you setting the depth collar on your jig base, match up the step of the drill bit with the 3/4" line you are referring to on the portable base and tighten the depth collar against the drill guide block.  Since you have the K3 bench top base you can double check and see that your drill bit will now be set for 3/4" settings. 

Hopefully this clears up any confusion on these markings.  If not please send me a message with your contact information and I can try to explain it better. 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Adaptive Cutting System/Saw Blade

I have had the ACS for about a year.  Was wondering if there any other blades, like a Diablo, that will fit the saw?Continue

Started by Randall H Gress in Beginners' Zone Feb 20.

AutoMaxx 6" clamp not working

I have been using the Automaxx 6" clamp for two plus years, and recently the clamp is impossible to close the handles to secure the work and my jig. I cannot close the handles no matter how much pressure I can exert. I open the clamp to max to reset…Continue

Tags: clamp, inch, 6, Automaxx

Started by Anthony M Calabrese in Other Kreg® Products Feb 12.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_