Kreg Owners' Community

What happened to the pnuematic screw gun that was part of the Kreg line of products a few years ago?  Thought it was a good idea, particular that it wouldn't overdrive the screw.  Was it discontinued?  Also, do any members use or have used a pnuematic screw gun?  If so, what's been your experience?

Views: 521

Reply to This

Replies to This Discussion


I've used pneumatic screw guns, in the past, for many fastening tasks.

They worked very well and were the tool of choice for driving threaded fasteners.

The pressure had to be monitored and constantly adjusted, so as to obtain the desired torque.

When the pressure dropped, the fastener wasn't properly seated.

You have to wait for the pressure to build up again, then proceed.  

Very large air pressure storage containers were needed---

not suitable for mobility.  A 20gal capacity tank is needed for continuous duty. 

We had and also used corded drivers; however they needed to be kept locked-up---

dam thieves would walk off with them.

Pneumatic screw guns are being replaced by the more favored cordless drivers.

These drivers feature a torque adjustment and provide more consistent torque, at a specific setting.

Most are heavier than a 2.5lb drywall screw driver.

The Milw M12 driver is very light weight.  I've used them nearly all day long, and my arms don't get tired.  

TIP:  use a holster or rig up a sling, akin to a sling on an AR15, or the like.

You don't have to worry about dropping it---

it's always in an at-the-ready location.



the Keg screw gun needs 16cfm @ 90psi.

It's like a typical drywall air-driven screw gun.

Also, that screw gun can be used for drilling the pocket holes.

The gun features a quick-change bit---

change from drill to drive in a couple seconds.

Also it has an integral reversing feature.

Thanks Ken. I have a Porter Cable driver that works well. It just doesn't have any adjustment capabilities; just have to rely on feel. I've run several screws through the wood. Looking for better control.


Without any adjustment feature, you'll have problems.

Some of those drywall drivers output is like 120 in lbs torque.

Are you using it to drive 5'' lag screws into landscape timbers?

For driving screws, the least expensive and reliable cordless driver is the Ryobi 18V model.

Does a great job for the money.

I've used 3 separate ones for quite awhile, and never experienced any issues.

This tool is also suitable for drilling, but limited to 1500 rpm.

I drill the holes with a Dewalt corded drill. I set the screws with a cordless porter cable driver. I thought if I went to a pneumatic driver I could get better control and not overdrive as much. The kreg driver had a video that indicated it would stop after depth reached.

Without an adjustable torque setting, stripping or over-driving will occur.

i'd suggest installing and seating the screws by hand, using a hand controlled driver, small ratcheting tool, or the like.  The opposite end of the square-tipped tool will fit into a 1/4'' hex driver.

You know Ken. I could use my Porter Cable cordless drill/driver. It has adjustable torque settings. Thanks for your suggestions!

Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 


  • Add Videos
  • View All


Recent Workbench Survey Legitimacy

Yesterday, I received an email wanting my opinion on Kreg adding high end workbenches to their product line and wanted to know before I clicked the link if this is a legitimate survey or some phishing scam. Here's the link I was provided (…Continue

Started by JOHN W. GOETZ in Other Kreg® Products Dec 10, 2021.

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11, 2021.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…


Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…


Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service