Kreg Owners' Community

Hello,

I needed to mate a 1 ½" main workpiece (the one to be drilled) with at 1" mating workpiece in a 90° attachment.

Using the various charts available online like https://www.dropbox.com/s/jvl0rf4kbwz4jrh/Kreg%20-%20Pocket%20Screw... or https://industrydiy.com/woodworking/kregtools/kreg-jig-settings-chart/ 

I set the jig and drill bit to 1 ⅜" and used 2" long screws (see attachment). Luckily I did a test fit and saw that the screws were around ⅛" too long, would have gone through to the other side of the mating workpiece.

So I used 1 ½" screws which seemed to be perfect.

Did I read the chart wrongly?

Any advice would be appreciated.

Thank you.

Views: 370

Attachments:

Reply to This

Replies to This Discussion

Hello Guy

It appears you did everything as advised on Kreg pdf. Is it possible your clutch setting was set too high. You were wise to do a test before actually assembling. I would hate to have that surprise if it were me.

Mike

Hello,

Clutch setting was set pretty low. On my Makita drill/driver it was set to setting 4 out of 16. But even if it was too high, it would merely strip the mating workpiece, due to the embedded washer in the screw head, the screw would never be able to make the screw head go below the bottom of the pocket hole.

It seems that 1 1" ¾ screw would have worked but Kreg doesn't make screws in that length, but I'd rather have the screw a little too short than too long and penetrating to the other side of the mating workpiece.

See photos of the settings of drill bit collar and jig height setting and screw penetration measurements for 1" ½ and 2" screws. 

I think Kreg chart had a typo, it needed a 1" ½ screw.

Good info. I am going to make a note of this on chart I down loaded. I would hate to mess up an expensive pc. of wood  over to long of screw.

Mike

I think I'll create an iPhone app to calculate the measurement below so that using various "non standard" size lumber, anyone using the jig and this app can verify screw clearance and penatration:

Pd - Penetration Depth

Pc - Penetration Clearance

Sc - Screw Tip Clearance

Sd - Screw Tip Depth

Hd1/2 - Hole Depth

Hb - Hole Bottom

Ht - Hole Top


try using the pan head screws. I believe that's what their dsigne for

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Recent Workbench Survey Legitimacy

Yesterday, I received an email wanting my opinion on Kreg adding high end workbenches to their product line and wanted to know before I clicked the link if this is a legitimate survey or some phishing scam. Here's the link I was provided (…Continue

Started by JOHN W. GOETZ in Other Kreg® Products Dec 10, 2021.

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11, 2021.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_