Kreg Owners' Community

I am in the process of making a corner cabinet but instead of using the easier way of butting the back sides of the cabinet, I want to make an angle backside. Cutting the backside is easy but I cant get the Kreg in the proper position to drill the pockets. Does anyone have a suggestion on how I can do this?

Views: 4678

Reply to This

Replies to This Discussion

Can you post a photo of what you're talking about so we can better understand the situation?
Remember, if you have a Kreg Jig or Kreg Jig Master System you can remove the Drill guide from the base completely. Then you can actually screw it to the workpiece if there's no good way to clamp it. If you have the Kreg Jig Jr. You can do the exact same thing... screw it into place on the workpiece.
For more information on what Derek mentioned... take a look at page 13 of the Quick Start Guide that came with your Kreg Jig...

I've included the Quick Start Guide here in PDF form. By utilizing your Spacer block and a SPS screw, you can secure the jig to the workpiece w/out a clamp and drill your holes from there! Good luck.
Attachments:
This is the picture of the cabinet. The back piece is cut 45 degree at both ends. Both back side pieces are cut at 45 degree also. So when both the back sides and the back piece are put together they form a right angle to the wall. The problem I am having is creating the pocket hole using the jig. I have the K-4 jig
Attachments:
Bill,

Are you mitering the back pieces at 45 degrees and then putting them together? Is there a picture of the cabinet from the top so we can get a better idea of what you are doing or maybe a drawing. If I could see this I'm sure I would be able to help you figure it out.
Dan

Here is a picture from top as you requested
Attachments:
Here's a bit more information on joining mitered corners with the Kreg Jig:


Not real sure what you're trying to do,but here goes.Pre-drill and countersink holes from the back side,then using #8 screws,secure the back to the sides. Drill these holes at the proper angle. Don't use the jig at all.
The problem I discovered with this process is you get end grain in the middle of the corner. It finishes different then face grain as you know. I would like to see a formula for splitting the angel and change the depth setting as stated in the beginning of this post.


Any help would be greatly appreciated.

Steve

KregRep said:
For more information on what Derek mentioned... take a look at page 13 of the Quick Start Guide that came with your Kreg Jig...

I've included the Quick Start Guide here in PDF form. By utilizing your Spacer block and a SPS screw, you can secure the jig to the workpiece w/out a clamp and drill your holes from there! Good luck.
what manual or pdf file is this miltered and angled joining info from... i would like a copy of this as i need all the help i can get --- really falling in love with woodworking, and want to learn more, and use my kreg jig to it's fullest potential :)

KregRep said:
Here's a bit more information on joining mitered corners with the Kreg Jig:


Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_