Kreg Owners' Community

Kreg KMS7102 Table Saw Precision Miter Gauge System and the DeWalt 745 Table Saw

Kreg Folks,

Is the Kreg KMS7102 Table Saw Precision Miter Gauge System compatible with the DeWalt 745 10" contractors table saw?

Thanks!

NIck

Views: 1790

Reply to This

Replies to This Discussion

I have the KMS7102---

that features a miter bar that fits miter slots 3/4" wide x 3/8" deep.

Hi Nick I have the very same table saw ,and the answer is yes the Kreg mitre gauge will fit the Dewalt saw. Their are small plastic adjustment screws on the side of the Kreg mitre gauge their hard to see because they are black , you simply adjust them in or out to fit your track . Make sure the gauge has no side to side free play  but loose enough so it slides easy up and down ,it takes a bit of patience and fine tuning . The idea of these adjustment screws is so the gauge can fit different tracks hope this helps Mick.

Used to have the DW 745 before I got a bigger saw.  I used the Kreg miter gauge on the DW 745 with little trouble, but it needed one important tweak:  The fence on the gauge is much longer than the available width of your saw's table to the left of the blade.  Therefore, even when you have adjusted the set screws in the miter bar so that it fits in the saw's miter track with no play, the weight of the fence is going to pull the bar up and out of the groove.  To combat this, and to prevent the fence from catching on the left front edge of the table when you move a workpiece into the blade, set up a support to the left of the table, at the same height as the table, for the left edge of the fence to ride on.  That will keep the miter gauge flat in the track, square to the blade, and prevent any catching by the fence that could screw up your cut.  I used a Triton folding stand with a piece of 3" PVC pipe in the jaw.  The miter fence rode along the crown of the PVC smoothly.  Look in the center of this pic and you'll see what I'm talking about -- the stand and pipe to the left of the DW saw.  Hope this helps.

Hey Russ - Was that a two car garage and you built a wall in the middle or was it a single car? I have a two car and I want really bad to build me a divider wall but I haven't convinced my wife yet. I keep scratching things off the "Honey-Do - List" so she may give in sometime soon. 

It was a one-car garage.  I'm surprised my wife didn't kill me for taking over the entire garage.  But that problem has been solved recently -- we bought a bigger house and I have commandeered a large portion of the basement for a new shop.  It's going in slowly -- the framing, electrical, and drywall are still in progress, but the layout and DC system are being developed.  I'll post a shop tour on my YouTube channel when the new digs are complete and I'm up and running again.  I'm sick of doing, framing, insulation, drywall, and electrical when I really want to be building furniture.  But none of those are as bad as trying to design a dust collection system!

 

Nice shop Russ , I made a extension table for my Dewalt saw to get over that problem.

Ken, Mike and Russ,

Thanks so much for your replies. Very helpful. And Russ, thanks for the photo. Bell well. -Nick

Nick,

Applying finishing paste wax in the miter bar track---bottom and "both sides", 

will reduce friction, resulting in less wear on the nylon set screws, that'll rub in the miter bar slot.

I've got the same table saw as you, and I can confirm that the Kreg miter gauge will indeed fit the Dewalt saw. There are small plastic adjustment screws on the side of the Kreg miter gauge, which might be a bit tricky to spot because they're black. You just need to adjust them in or out to align with your track. Ensure there's no lateral movement in the gauge but that it still moves smoothly up and down. It may require some patience and precise adjustments, but these screws allow the gauge to adapt to various tracks. #รถ

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

The Pocket Hole Joinery Book - Review

Posted by Daris R. on August 27, 2024 at 8:29pm

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_