Kreg Owners' Community

I know that I am doing something wrong, just not sure what. 

 

After I clamp the jig to my wood and start to drill the jig starts to walk to the r ight a little bit.  I have the pressure of the clamp pretty tight, any more and I would be afraid of breaking the jig.  The wood is fairly slick and the bottom of the jig is too,  what gives?

Views: 199

Reply to This

Replies to This Discussion

I have had this problem before.  I usually reposition the clamp and the jig.  What kind of clamp are you using.  I made my own from a welding clamp (vice grip type) and some flat washers and of course a welder.  It seems to work well for me and I could customize the foot that would be on the bottom of my work surface to spread the clamping force over a larger surface.  I will post a pic of it.
I've clamped that little guy under some serious pressure and he's stood up to everything I could throw at him. I'd be more worried about denting the wood.
Could using lower RPM's on the drill cause this?  I had my drill set in low gear for torque,  I later went back and did some more holes using the higher gear and things went fine,  not sure if it was due to drill RPM or something else.  

A few things to consider...

 

1) Your drill may not be sharp.  Check it, and send it into Kreg for resharpening if necessary.

2) Make sure you're clamping hard enough (you said you were).

3) Use a higher-RPM drill.  

4) Make sure the drill is at full RPM before engaging the wood.

 

Turned out it was drill RPM,  I was using a cordless drill that had 5 year old batteries on their last leg.  A new battery and setting the drill on the higher RPM setting got rid of the problem. 
Hi Patrick - Thanks for the feedback, good information to know. I wouldn't have guessed drill rpm would give that symptom.

I haven't experienced any problems with the drill or guide moving/walking.

I use one of my drills, that has 2000 to 2500 RPM.

Slower rpm drills, such as with most cordless tools, don't have a high enough RPM, to make smooth cuts.

The higher speeds cut much smoother and faster--akin to a router---higher rpm will result in smoother cuts.

 

I drill the holes part way in, back it out to remove the chips---repeat as necessary, then continue until the drilling operation is complete.  

The drill bit needs to turn at a fast enough rpm, so the flutes on the drill bit, carry the chips out the top-side.

 

The Kreg drill bits and be sharpened, using ''diamond'' needle files.

I use the diamond files, made by EZE-Lap---they work great.

Various file shapes are available----vary handy tools for your tool box/work-shop.

 

You need a good light, along with a magnifier, so as to enlarge the viewing area, a 2-1/2 X power is sufficient.

 

Works for me.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

1 Parts

Parts

Videos

  • Add Videos
  • View All

Forum

Parts

The Clamp anchor screw broke on my mobile project center.  How can I acquire a replacement?Continue

Started by Jon J Howard in Beginners' Zone yesterday.

Rip-cut ACS plunge saw

Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Got the original ripcut and didn't really like it had trouble cutting straight. New one has several improvements should make it work much better. especially…Continue

Started by William Burt Brown in General Woodworking Mar 17.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_