Kreg Owners' Community

How can I make sure I use the right pockets screws for my projects.

Views: 771

Reply to This

Replies to This Discussion

Jacob , if you look on my home page  there are two pictures of a chart  that may help you , they are number 5 and 6  , happy wood working , JIM

Thx Jim

 your  welcome , hope the chart helped , JIM !!

Jacob Golab said:

Thx Jim

Hi Jacob. We have a lot of information available to help you choose the correct screw.

You can find information in your Kreg Jig owner's manual.

For a good basic chart, you can go tho the Kreg Jig Screws and Plugs page at kregtool.com, and then click on the "Screw Length" button.

To get even more information, check out the Kreg Plus Newsletter from February 2012. It has a chart you can download, and a link to a video that tells you just about everything you'd want to know about Kreg Screws.

KregRep

For many of us it goes without saying. Try the screw length on a test piece first.

The screws can be cut shorter with a good pair of high leverage linemen's pliers.

Personally I wouldn't cut the screws shorter---the effective leading end will be destroyed.

Re-position the drill stop, closer to the drill tip, so the drilled hole will not be as deep.

Thats easy rule of thum anything 3/4" you use a 1 1/4" but hard woods you use fine thraed and soft woods you use you use corse thraed. I use the K-2 so I dont none moch about the longer one's if Im not worng they got a chaert that you can print.

I am having trouble with this too I think.  Using 23/32 plywood and attempting to join a side panel to a bottom panel, with the side panel on top, it seems if I have the pockets drilled on the inside of the side panel, the screw tips poke through the bottom panel to the outside of the work piece.  I am certain of my jig setup and I am using 1 1/4" coarse thread screws.  Of course, when putting the pockets on the outside of the panel, there is no problem.  But that is not what I want.  I want the pockets on the inside.

John,

You can make your desired joint by setting the stop collar slightly closer to the drill bit tip as Ken suggested. My experience has been that the pocket holes on the inside tends to split the ends of the receiving board even when you you the correct screws. I opt for a different joint type if I can't keep the pocket holes on the outside.

Jacob try this use a nickle and a dime to set your collar and set your drill at 8 or 9 that is for only plywood thow. 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Adaptive Cutting System/Saw Blade

I have had the ACS for about a year.  Was wondering if there any other blades, like a Diablo, that will fit the saw?Continue

Started by Randall H Gress in Beginners' Zone Feb 20.

AutoMaxx 6" clamp not working

I have been using the Automaxx 6" clamp for two plus years, and recently the clamp is impossible to close the handles to secure the work and my jig. I cannot close the handles no matter how much pressure I can exert. I open the clamp to max to reset…Continue

Tags: clamp, inch, 6, Automaxx

Started by Anthony M Calabrese in Other Kreg® Products Feb 12.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_