Kreg Owners' Community

Hi all,

Fairly new kreg user but have had no issues with past small projects using 1x4, 1x6,etc.  Starting a laundry pedestal build that uses 2x4 with pocket holes on te cross braces for top and bottom.  

Setting jig on 1-1/2 and setting collar as I have in the past.  When I go to screw the 2-1/2 " pocket hole screws, they ALL have come out of the other side of the 2x4.  I've had to back them out, so now the joint is not tight.  

Any tips on what might be happening?  I think it might have to do with the collar on the bit - I don't think there is enough "neck for the drill chuck to grab.

Views: 2351

Reply to This

Replies to This Discussion

One of the 2 settings is definitely 'off'.

Which Kreg jig are you using?

One double-check method to verify the drill bit collar setting, is to place the bit into the jig and a nickel (5¢) underneath the tip of the bit. Lock in the collar at the top of the jig.

There are really only three "settings" associated with a Kreg Jig:

1. Distance from end of the jig to the edge of the pocket hole material. This is used to ensure that the screw exits the pocket hole piece at the center of its thickness. You'll be able to determine if this setting is off by driving a screw, removing it, and seeing where the screw exited the pocket hole piece.

Note that the Kreg Micro Jig also uses this setting to create a "deeper" pocket hole to hide the screw pan head in 1/2" material. In this usage the screw will exit off to one side of the pocket hole material, rather than in the center of the thickness.

2. Step drill stop collar position. This is used to stop the drill depth at the point just before the drill tip would exit the pocket hole piece. As Scott had mentioned, the target depth is about a nickel's thickness shy of exiting the pocket hole piece. If your pocket hole is too deep, then you might be drilling into the jig base (depending on your jig model), or you might be drilling through the pocket hole piece (look for a drill hole). If the drill depth is too shallow, this is not likely to result in the screw exiting the non-pocket hole piece.

You may want to check the drill's stop collar position after drilling the pocket holes - just to make sure it hasn't slipped while drilling.

3. Screw length. Since the depth of the pocket hole is fairly constant (leaving a nickel's thickness of undrilled wood) the screw length is what determines how far the screw will penetrate the non-pocket hole piece. Too short a screw won't have as much holding power. Too long a screw will exit the far side of the pocket-hole piece. I think this is one of two possible reasons that your screw is exiting the piece.

There is actually a second possible reason that your screw is exiting the piece, and that is "over-driving" the screw through the pocket hole. This can happen if you're using an impact driver rather than a clutched driver. If you can picture it, your pocket hole is formed with the tip stopping a nickel's thickness from the piece edge, and the screw head platform being formed the drill tip's length from that. Over-driving forces the screw head past that screw head platform. Excessive over-driving could drive the screw all the way through the pocket hole piece. Without cross-sectioning the pocket-hole piece I'm not sure how you'd determine if you're over-driving the screw.

I think the two best bits of advice I've read on this forum is the suggestion to use a nickel to check the drill depth (collar) setting, and the suggestion to make test pocket hole joints using scrap material before committing to using the project material.

When fastening 2x (1-1/2") and thicker material, I use the HD jig---NO problems.  WorksForMe.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

Videos

  • Add Videos
  • View All

Forum

Pocket Hole Drawer Slide Brackets?

Hello - I have a couple of workbenches in my 'shop' and am contemplating putting 2 or 3 pull out bins on the bottom shelves of both. I've not worked with drawer slides before and am looking to make it simple(r). Thinking of making 2 sets of pocket…Continue

Tags: hole, pocket, basket, slide, Drawer

Started by E M Hampton in General Woodworking on Monday.

Kreg Jig 5 Clamp Busted 1 Reply

My clamp to hold boards to my kreg jig no longer works.  It won't move from it's spot and when I push the grey button on top, nothing happens.  are there replacement parts for this?Continue

Started by Tammy in Beginners' Zone. Last reply by John Browne Jan 3.

Product Reviews

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 2 Comments

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am — 2 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_