Kreg Owners' Community

Dear Kregeers,

I would like to try and build a farmhouse table with extensions in the middle to seat 12.

I have seen some plans on Ana White and Buildsomething, along with others. Unfortunately, most, if not all the plans are for extensions at the ends of the table.

Is there any one that could make some plans for me? Of course, I am willing to pay for the plans.

I know I need to buy some slider hardware and stablilizers- Rockler?

I would really appreciate an direction I may receive from those of you that have more experience than I do. 

I am not an expert by any means, but I have used a drill, saw, hammer,etc. I bought a Kreg master Jig set, clamps, nail case with assorted Kreg screws, and the saw rip guide.

Your assistance will be appreciated. Thanks!

Views: 341

Reply to This

Replies to This Discussion

I have built one of these in the past, you need hardware for the sliding mechanism for sure.  The average table that I make is 36" wide and 72" long.  Figure a 1" to 1 1/2" overhang on all sides for your top.  Based on 1" overhang, your base needs to measure 34" wide and 70" long, your leg size will determine what your apron sizes will be.  Your long side aprons will need to be cut in half in order to slide apart, the table top needs to be made at least an inch or two wider than what you'll need and will need to be cut in half.  Once you get the base and top done, lay your top upside down on the workbench and then place your base on top, to install the sliding mechanism.  You will need to make your leaves or leaf depending, open your table up and put your leaf inside, NOW is the time to cut your top to width, with the leaf/leaves inside of it. You will need to mark locations for dowels/etc. for when the top is closed. I make my leaves with a side apron that is held on with table top fasteners.  Hope this helps!

Thank you Justin. I’ll do my best to follow the instructions. I am a beginner- measure twice, cut once. Thank you.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_