Kreg Owners' Community

Hi Everyone,

My first time post all the way from Edinburgh.

I recently was given a K5 jig from my wife for a Christmas present. Its a great upgrade from what I was using but the only problem I have with it is finding the right adaptor to fit my vacuum extractor!

It needs an interior fit for a 30 mm  entry on the jig and I have a 38mm hose extraction in my workshop. Anyone got any ideas about possible suppliers??

Brian Mundey

Views: 107

Reply to This

Replies to This Discussion

I have an old hose from an original ShopVac. That ends fits inside perfect. There are step reducers on Amazon I believe. I got one from my local Lowes store. Maybe your local lowes/Home Depot type store has them in their shop vac aisle.



Glen S said:

I have an old hose from an original ShopVac. That ends fits inside perfect. There are step reducers on Amazon I believe. I got one from my local Lowes store. Maybe your local lowes/Home Depot type store has them in their shop vac aisle.

Hi Glen,

Thanks for the info. I'll give it a try

Brian M

I also bought a K5 a while back, but only started using it about two days ago. I don't have a dedicated dust extraction system, so I don't know if my fix will work as well for you as it seems it will for me, but I also recently bought a Bosch vacuum with an adaptor that is supposed to allow you to attach the hose to a powertool's dust extraction duct, and I have already used it with success on my circular saw and my router.

When I compared the diameters of the adapter and the K5's extraction duct, however, I could immediately see the one would never fit into the other, so initially I thought I’d just make do without the dust extraction feature, but I very quickly found out that the drill shavings clog up the jig and drill bit to such an extent that it becomes very difficult to remove the bit from the hole and you really have to move the bit up and down very frequently to keep removing the shavings from the hole in order to prevent the bit from becoming stuck in there!

I therefore had to work out a way of connecting my vacuum to the jig, so I measured the inner diameters with a vernier caliper. The Bosch adapter is 32 mm and the K5 35 mm, so today I bought a simple 25 mm plastic pipe connector at the local hardware shop. The outer diameter is pretty close to 32 mm, so it's a tight fit in the adapter, but easy enough to insert and remove.

I then wrapped some duct tape around the other half of it until it was a tightish fit into the K5's extraction duct, but could still be removed quite easily. With the connector inside the duct, I drew a line on it where it should be cut away to make the airflow as smooth as possible, and then took it out again and cut it out with my dremel tool. I then mixed up some epoxy I still had left over from another little project, applied it to the outside of the connector and slid it into the K5's extraction duct.

I hope the photos will give you some idea of what I did.

I also bought a K5 a while back, but only started using it about two days ago. I don't have a dedicated dust extraction system, so I don't know if my fix will work as well for you as it seems it will for me, but I also recently bought a Bosch vacuum with an adaptor that is supposed to allow you to attach the hose to a powertool's dust extraction duct, and I have already used it with success on my circular saw and my router.

When I compared the diameters of the adapter and the K5's extraction duct, however, I could immediately see the one would never fit into the other, so initially I thought I’d just make do without the dust extraction feature, but I very quickly found out that the drill shavings clog up the jig and drill bit to such an extent that it becomes very difficult to remove the bit from the hole and you really have to move the bit up and down very frequently to keep removing the shavings from the hole in order to prevent the bit from becoming stuck in there!

I therefore had to work out a way of connecting my vacuum to the jig, so I measured the inner diameters with a vernier caliper. The Bosch adapter is 32 mm and the K5 35 mm, so today I bought a simple 25 mm plastic pipe connector at the local hardware shop. The outer diameter is pretty close to 32 mm, so it's a tight fit in the adapter, but easy enough to insert and remove.

I then wrapped some duct tape around the other half of it until it was a tightish fit into the K5's extraction duct, but could still be removed quite easily. With the connector inside the duct, I drew a line on it where it should be cut away to make the airflow as smooth as possible, and then took it out again and cut it out with my dremel tool. I then mixed up some epoxy I still had left over from another little project, applied it to the outside of the connector and slid it into the K5's extraction duct.

I hope the photos will give you some idea of what I did.

I also bought a K5 a while back, but only started using it about two days ago. I don't have a dedicated dust extraction system, so I don't know if my fix will work as well for you as it seems it will for me, but I also recently bought a Bosch vacuum with an adaptor that is supposed to allow you to attach the hose to a powertool's dust extraction duct, and I have already used it with success on my circular saw and my router.

When I compared the diameters of the adapter and the K5's extraction duct, however, I could immediately see the one would never fit into the other, so initially I thought I’d just make do without the dust extraction feature, but I very quickly found out that the drill shavings clog up the jig and drill bit to such an extent that it becomes very difficult to remove the bit from the hole and you really have to move the bit up and down very frequently to keep removing the shavings from the hole in order to prevent the bit from becoming stuck in there!

I therefore had to work out a way of connecting my vacuum to the jig, so I measured the inner diameters with a vernier caliper. The Bosch adapter is 32 mm and the K5 35 mm, so today I bought a simple 25 mm plastic pipe connector at the local hardware shop. The outer diameter is pretty close to 32 mm, so it's a tight fit in the adapter, but easy enough to insert and remove.

I then wrapped some duct tape around the other half of it until it was a tightish fit into the K5's extraction duct, but could still be removed quite easily. With the connector inside the duct, I drew a line on it where it should be cut away to make the airflow as smooth as possible, and then took it out again and cut it out with my dremel tool. I then mixed up some epoxy I still had left over from another little project, applied it to the outside of the connector and slid it into the K5's extraction duct.

I hope the photos will give you some idea of what I did.

I also bought a K5 a while back, but only started using it about two days ago. I don't have a dedicated dust extraction system, so I don't know if my fix will work as well for you as it seems it will for me, but I also recently bought a Bosch vacuum with an adaptor that is supposed to allow you to attach the hose to a powertool's dust extraction duct, and I have already used it with success on my circular saw and my router.

When I compared the diameters of the adapter and the K5's extraction duct, however, I could immediately see the one would never fit into the other, so initially I thought I’d just make do without the dust extraction feature, but I very quickly found out that the drill shavings clog up the jig and drill bit to such an extent that it becomes very difficult to remove the bit from the hole and you really have to move the bit up and down very frequently to keep removing the shavings from the hole in order to prevent the bit from becoming stuck in there!

I therefore had to work out a way of connecting my vacuum to the jig, so I measured the inner diameters with a vernier caliper. The Bosch adapter is 32 mm and the K5 35 mm, so today I bought a simple 25 mm plastic pipe connector at the local hardware shop. The outer diameter is pretty close to 32 mm, so it's a tight fit in the adapter, but easy enough to insert and remove.

I then wrapped some duct tape around the other half of it until it was a tightish fit into the K5's extraction duct, but could still be removed quite easily. With the connector inside the duct, I drew a line on it where it should be cut away to make the airflow as smooth as possible, and then took it out again and cut it out with my dremel tool. I then mixed up some epoxy I still had left over from another little project, applied it to the outside of the connector and slid it into the K5's extraction duct.

I hope the photos will give you some idea of what I did.

My unreserved apologies! I tried several times last night to add my reply, but got a message every time that there was a problem with the page, so I never realised that they actually had been added! No pictures though. Have no idea what's up with that...

Still trying to upload some photos...

Still trying to upload some photos...

Still trying to upload some photos...

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Adaptive Cutting System T-Track Stops Mod 1 Reply

I bought the ACS a couple of weeks ago & have been pleased with the results on my first small project (LP record crates)... I was disappointed with the plastic accessories for the table-top, especially the T-Track stops. I'm pretty sure they…Continue

Started by John Moore in Beginners' Zone. Last reply by Deac Manross May 17.

Kreg screws in the UK 3 Replies

Hi guys, I'm having real trouble finding reliable stockists of Kreg screws over in the UK. I'm based in Northampton and can never find what I need. Can anyone recommend a UK stockists that also delivers?

Started by Allen Causebrook in Miscellaneous. Last reply by KregRep 1 hour ago.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_