Kreg Owners' Community

Before I get into the shop and spend time experimenting with scrap wood I want to know if anyone has already figured out the correct settings for joining two different thicknesses of boards.  I am specifically interested in joining a 3/4" board to a 1/2" board.  One could setup the jig as if two 1/2" boards were being joined.  Even though the screw is not in the center of the joint the world wouldn't end.  However I like precision and that wouldn't cut it.  My guess, before testing, would be to set up for a 3/4" joint but to use a 1" screw rather than the 1 1/4".  I searched the Kreg info and can not find this issue addressed anywhere.

Anyone want to save me some time?

Views: 31782

Reply to This

Replies to This Discussion

A picture speaks a thousand words!! Great diagram Kurt!
I like the chart Dan. Can you just verify that it is correct where (and perhaps summarise why) it shows the jig settings fluctuating (ie, decrease, increase and decrease, etc,) as it goes across the page whereas it only shows the corresponding thickness of the attaching workpiece as increasing.

Douglas Golding said:

Dan said:
This thread has already been referenced, but it has some good info in it

Attached is a pdf file that you may come in handy.

I just did this my self, while making the vanity. The drawer sides are attached to the drawer front, sides are 1/2" front is 3/4" make pocket holes in 1/2" and use 1" screws to attach.

According to the drawing, we use the Kreg setting for the thickness of the wood we're drilling into, and the screw length for the wood we're fattening to? This is how I interpret it.
I just made drawers using the pocket hole setting for the thickness of the wood into which I was putting the pockets (3/4"), and the screw length for the wood to which I was fastening (1/2"), and it worked great - as long as I used a gentle touch, and didn't overdo it. (I had 2 tips pop slightly through.) Go easy on a lower power (my drill has two settings for power - I used #1), and still drilling the moment it tightens.
It doesn't always work to drill into the thinner stock - my 3/4" drawer fronts & backs sit between the 1/2" drawer sides. I don't understand why the Kreg site doesn't address this. This is a pretty common way to make drawers.

Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 


  • Add Videos
  • View All


Replacing existing slides but cannot remove drawer front

The Kreg slides are made to work with new drawers before putting on the drawer front. In my situation, I cannot remove the existing fronts which means when reversing the jig to hold the draw, it’s at an angle. Not sure what I should do to make them…Continue

Started by Jay Homeyer in General Woodworking Apr 25.


The Clamp anchor screw broke on my mobile project center.  How can I acquire a replacement?Continue

Started by Jon J Howard in Beginners' Zone Apr 20.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…


Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…


Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service