Kreg Owners' Community

This is why you should have a separator with your dust collector system.This is Maple that I am planning and it is about 1 hours worth of continuous planning.Could not imagine the mess my grand kids would have to sweep up for me,haha

Views: 192

Attachments:

Reply to This

Replies to This Discussion

Thanks Robert

Robert Melrose said:

Here it is so everyone can see without clicking on the link.
Amazing isn't it? Quite a bit gets by too. I've had one of those lids for some time now but was still changing vac bags faster than I liked. Then last time I got bags they were nearly $10 ea!!! I just put a Dust Deputy on last week, we'll see how that goes.
I think that I get 90-95 % of chips when planning.And when just using table s aw the cyclone don't get hardly any sawdust. I usually shake my bag after I shut down the shop in evening and quite allot of dust falls in the plastic bag.What is a dust deputy??

John Schaben said:
Amazing isn't it? Quite a bit gets by too. I've had one of those lids for some time now but was still changing vac bags faster than I liked. Then last time I got bags they were nearly $10 ea!!! I just put a Dust Deputy on last week, we'll see how that goes.
Hi Jens - Dust deputy is a little more of a sophisticated (read pricier) cyclone system made by Oneida Air Systems. Seems to be working pretty good, Have gathered a lot more in the bucket after doing a lot less work but I have set up any real quantitative testing on it. I grabbed it off Rockler when they had a 20% off coupon floating around as I seldom see these things discounted.
Let's see if this link will work:
http://www.rockler.com/product.cfm?page=22062&filter=dust%20deputy

Jens Jensen said:
I think that I get 90-95 % of chips when planning.And when just using table s aw the cyclone don't get hardly any sawdust. I usually shake my bag after I shut down the shop in evening and quite allot of dust falls in the plastic bag.What is a dust deputy??

John Schaben said:
Amazing isn't it? Quite a bit gets by too. I've had one of those lids for some time now but was still changing vac bags faster than I liked. Then last time I got bags they were nearly $10 ea!!! I just put a Dust Deputy on last week, we'll see how that goes.
Attachments:
so it is for the 5 gallon buckets,I also have one of those that I use for my sanders and small tools

John Schaben said:
Hi Jens - Dust deputy is a little more of a sophisticated (read pricier) cyclone system made by Oneida Air Systems. Seems to be working pretty good, Have gathered a lot more in the bucket after doing a lot less work but I have set up any real quantitative testing on it. I grabbed it off Rockler when they had a 20% off coupon floating around as I seldom see these things discounted.
Let's see if this link will work:
http://www.rockler.com/product.cfm?page=22062&filter=dust%20deputy

Jens Jensen said:
I think that I get 90-95 % of chips when planning.And when just using table s aw the cyclone don't get hardly any sawdust. I usually shake my bag after I shut down the shop in evening and quite allot of dust falls in the plastic bag.What is a dust deputy??

John Schaben said:
Amazing isn't it? Quite a bit gets by too. I've had one of those lids for some time now but was still changing vac bags faster than I liked. Then last time I got bags they were nearly $10 ea!!! I just put a Dust Deputy on last week, we'll see how that goes.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_