Kreg Owners' Community

I would like to build my new kitchen cabinets I'm interested what the kreg family has input about this. I also looking for plans so I can build them. Thank you

Views: 2234

Reply to This

Replies to This Discussion

Stacy,

My approach would be to do a search for books on "cabinet making"---

do a search on www.

There are some out there that are very informative.

You need to learn of the various joinery techniques, that are proven to be very useful for successful builds.

Thank You Ken. I'll start looking for books on making cabinets. Thanks again for the info.

Be sure to check out our new line of Hardware Installation Solutions. You'll also find lots of tips in our new video series: Kreg Kitchen Makeover. We list a variety of online sources where you can find free project plans here

Stacy,

There is a video on basic cabinet building by Jay at Jays Custom Creations.  To get it go to www.jayscustomcreations.com ; then click on the sketch up heading.  Drop down to "making cabinets" and click.  There are numerous other videos also available.

From my personal experience building a new bathroom vanity either purchase or make some assembly squares to insure your panels are kept square during construction.

Hope this helps, Don

The door made here look pretty cheap.  That strip that holds the panel in looks like a rail road tie added to the door frame.  Any thicker and you would not have any room for dishes.  Cutting the plywood panel corners off made it even that much worse.  Much better to cut the dado deeper and cut the corner square using a simple chisel.  The you could use a simple 1/4 inch square piece to hole in the panels and place it on the inside rather that the top of the stile and rails.   Using a simple table saw a person could cut and make a much better looking door in about the same length of time that would look more professional than is shown in this video.  The door would be a simple tendon and mortise type  style and you only need the saw fence and miter guage to cut the total door.  Pocket screws and never a good method of doing cabinet doors if you want a job that looks professional.   I could say much more but won't at this time.


 
KregRep said:

Be sure to check out our new line of Hardware Installation Solutions. You'll also find lots of tips in our new video series: Kreg Kitchen Makeover. We list a variety of online sources where you can find free project plans here

Hello, look up Ana White's web site. She has some very easy to understand kitchen cabinet plans on it. Kreg used to have a basic cabinetmaking booklet download that showed everything you need to build cabinets. I built my own for my cabin, I'm not a woodworker yet they turned out fine and I was able to make them the exact sizes that I needed. You can do it too.

Attachments:

Google Ana White and do a search on her site for kitchen cabinets. They are made with pocket holes and look amazing and she has free drawings and plans on her site.

I agree with Jay, a simple tongue/groove flat panel door would be just as easy to make and the results would be much better on a door.  Pocket screws definitely have their place, but not in a cabinet door, in my opinion.
 
Jay Boutwell said:

The door made here look pretty cheap.  That strip that holds the panel in looks like a rail road tie added to the door frame.  Any thicker and you would not have any room for dishes.  Cutting the plywood panel corners off made it even that much worse.  Much better to cut the dado deeper and cut the corner square using a simple chisel.  The you could use a simple 1/4 inch square piece to hole in the panels and place it on the inside rather that the top of the stile and rails.   Using a simple table saw a person could cut and make a much better looking door in about the same length of time that would look more professional than is shown in this video.  The door would be a simple tendon and mortise type  style and you only need the saw fence and miter guage to cut the total door.  Pocket screws and never a good method of doing cabinet doors if you want a job that looks professional.   I could say much more but won't at this time.


 
KregRep said:

Be sure to check out our new line of Hardware Installation Solutions. You'll also find lots of tips in our new video series: Kreg Kitchen Makeover. We list a variety of online sources where you can find free project plans here

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone Jul 22.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_