Kreg Owners' Community

Assembling a substructure piece of a current project I broke three screws.  The only way I know to recover is make new pieces.

This was using white oak.  Should the holes be pre-drilled in piece "B" before driving screws??  Never had to do this with red oak or soft maple.

Views: 1179

Reply to This

Replies to This Discussion

George,

Depending on the density of wood you are screwing into it can cause additional issues with joining your material. First off I'm assuming that you are using our fine threaded screws since you are working with hardwoods. If this is not the case that would be your main issue.

With harder words like this the best technique is to drive your screw part way in and then back it out some and continue this process until the screw is all the way in. This will allow the threads of the screw to be cleared making it easier to drive. Another tip would be to coat the threads of your screw with beeswax or paraffin wax to lubricate them going into your material. Using these tips you should be able to have success with this material and our screws.

When installing screws in hardwood, I use "screw lube", and don't have any issues with screws breaking.

Hi George,

I work a lot of hickory and on occasions a screw will break off.  It is not as common in installing a screw as it is when removing one.  What I have is a small 1/4 inch hollow screw extractor of which is actually a small shaft of steel with teeth cut in the end.  The process is quick and easy and how it works is by cutting a plug of wood from around the screw.  Once drilled down below the length of screw, pop out the wood containing the screw and then plug the hole using a 1/4" dowel of either the same species of wood or even just a plug that you glue back into the hole.  They are similar to a hole saw only longer and smaller.  It is a cleaner looking and easier repair than drilling a series of holes around the screw using a 1/8 dia bit, popping out the wood with the screw and then re-drilling the area with a larger bit and then plugging it. 

These are available at some woodworking specialty sources and come in a set if 1/4- 5/16 and 3/8 and or you can make one using a thin wall tubing of which you use a file and cut teeth in them.  They are not cheap however worth their weight in gold once you need one.  You save the cost on the wood that you have to replace and sometimes it is not possible to replace the part.  I think I got mine from Lee Valley Tools but it has been a good ten years agoi.  I have used them several times on dis-mantling of furniture as well as cabinet modifications. 

Kreg has also changed the screws.  It is my understanding, and I could be wrong, but the older dark colored screws had a dry lube on them and the new bright screws do not.

Hope Kreg will chime in and either verify this or say it isn't so.

George I did some checking and Rockler has them.  They are actually cheaper than I thought.  

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_