Kreg Owners' Community

I checked with my Lowes and they have 8 on order haven't gotten any yet.

Views: 10049

Reply to This

Replies to This Discussion

I talked to Lowes tool department today and they project 2 weeks before they are in the store.

I ordered mine on Apr 2 from Factory Autorized Outlet and it is suppose to be her on the 11th. The url is http://www.factoryauthorizedoutlet.com/porter-cable/nav/kreg/Precis...

They have a large selection of Kreg products.

You can actually order it from the Kreg site, now.  Haven't found 1 in Toledo, OH. 

 

Rod

WENT ON AMAZON AND ORDERED IT, WILL GET IT BY THE END OF THE MONTH AND IT WAS LESS THAN ANY WHERE ELSE I CHECKED.

Just received an email from UPS mine should be here the 11th

Received Mine today. Haven't made any cuts as my shop is not completely setup. I see one problem with my saw and that is the finish cut there is not enough tail support from the rip-cut

I got mine tonight and will attach it to my saw and give it a whirl tomorrow.  I go to the doctor first thing to see if I have to have surgery for carpal tunnel and THEN I will play with my new tool!

My lowes has them in picked one up. They got 8 only 1 on the shelf. I am getting ready to set it up.

Here is the results I used a warped piece of mdf the jig cut straight and the scale on the jig was right on for the length of the cut. The edge was not factory but very little sanding it would have been good. The saw used was a cheap $60 Porter Cable Saw from Lowes with the original blade.

 

 

 

Ordered from Amazon.  Delivery in May.

My local Lowes didn't have them yet so I drove to one about 20 miles away.  I still haven't put it on my saw yet.  I went to the doc and have carpal tunnel in both hands and right now they are giving me fits because I still keep trying to do all I need to do before surgery.  I am hoping the rip cut actually helps my husband cut a straight line.....

Just checked my local Lowes.  It's in stock and I'm picking it up this afternoon. 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_