Kreg Owners' Community

Hi,

I was looking up information on The Woodworking Show coming soon to my town and saw that Kreg is a sponsor... I was wondering if Kreg will be displaying at the show and if there will be any show specials that are too good to pass up?

Thanks!

Views: 359

Reply to This

Replies to This Discussion

Last Saturday was the show in Milwaukee and I got the master kit with extras and videos for $229.
They had some reduced prices on other products also.
What sort of extras? The master kit itself can be found for $139 at most places. What did you get for the extra $90?

Thanks
I got a corner clamp, face clamp,the 1/2" block & drill bit with the shorter screws, the the screws kit in the plastic case, the videos,and the single guide.
I was just at the Atlanta show last weekend and Kreg didn't offer any specials. I waited to purchase the K4 at the show, thinking that they would have a discount and they were giving away a free 6" square drive for the first 100 customers. To my surprise, they didn't have any K4's at the show, no free gifts and no discounts. Check Rockler, their offering a special.
I, too, saw the Kreg coupon for the 6" square drive for the first 100 customers. Sad that there were no specials at your show... did you at least get the free square drive?

A few weeks ago, Rockler gave a free right angle clamp with the K3 system. Now, it's a free large face clamp.

I just wanted to see if the show was worth the $8 admission (with coupon). Is the show worth attending? What kinds of things are there? I've never been to one before.

Thanks.
No, I probably was within the first 30-40 person at their booth and they told me that they ran out already. My guess is that the square drives never got shipped to the trade show, so they never did have any to give away to begin with. Same thing with the K4's, the representative said they never got shipped to the show. I wrote their customer service about my thoughts and especially about not even offering a show discounts like every other vendor did. They said that someone would reply within 24 hours and to this date, they never responded.

The trade show is well worth going to, like I said earlier, every other vendor offered some really great deals. Because of the that, I purchased many items that I would of normally of waited, but couldn't resist the offers. I will say that Kreg had great demonstrations of their products and it helped me with my decision to purchase the K4. I also own their precision router table and love it.
Not to stray off topic but what other types of deals did you see at the show?

I hope Kreg gets their shipping in order for our show here in a few weeks...
I did receive a response from a Kreg representative this morning and he was very apologetic. Apparently there was suppose to be a special bundling on the K3 outfit, which I never knew. Anyway, I was glad that to hear from him and that he was concerned.

As far as the deals, there were too many to talk about. Every vendor offered a price reduction of some sort. I would have to say anywhere from 10-20% off and/or bundling with a lower price. Peachtree Supply offered some great deals on their dovetail jigs, clamps and discounted all products they had at the show. I could of spent a fortune there. It's well worth going and go online and print the coupons they offer.

Enjoy!!
They should be apologetic and make it up to you by giving you a K3 kit for free ;)

Anyways, I hope Kreg does have some good offers at the show here. Hopefully, an official representative can reply to this thread.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_