Kreg Owners' Community

Ok, I have to admit, I have used the same clear bag over and over again for almost a year now, just dumping it into the trash cans when full, however, my trusted bag has sprung a hole.  Why am I not surprised that Harbor Freight doesn't sell the replacement clear bags?  I know quite a few folks have bought this machine, any idea where to get replacement bags?  I appreciate the help!!

Views: 2592

Reply to This

Replies to This Discussion

coo

Robert Melrose said:
Woodcraft sells them
Thanks a ton, I was a little shocked that HF didn't sell them, but the lady was nice enough to swear that a cloth table saw bag is what I was looking for. LOL
http://www.grizzly.com/products/category.aspx?key=180020

try this place have stores in Muncy Pa
Thanks Jens! Happy Holidays!
Same to you Justin
Little trick as far as bags breaking. I have found out that if you put your bag inside of a 33 plastic garbage can and set this in your frame ,that way when your bag is full just take the can and all out and dump it. I have cut a vertical slot on side of can you can see when it is getting time to dump.
Maybe you already have this setup I dont no . I no one thing since I added the cyclone garbage can lid can my plastic bag is not filling up as quick
I haven't taken the time to get my seperator finished yet, but that is something I need to do and never did think of the trash can idea, I will use that too. I went to Grizzly, do all clear lower bags fit the HF?
I would measure the ring on the collector and look for a bag that size I would think 20" or so Ill measure mine and see if I can help you out


justin waldron said:
I haven't taken the time to get my seperator finished yet, but that is something I need to do and never did think of the trash can idea, I will use that too. I went to Grizzly, do all clear lower bags fit the HF?
http://www.grizzly.com/products/1-1-2-HP-Dust-Collector-with-New-Im...

This is compatible to ours and it is a 19-1/2 inch bag which will do you right Check your ring and see.You can call Grizzley and they will be very happy to serve your needs
Justin I bought my bags to replace the original ones on my total shop dust collector from penn state industries. I also built a cyclone that was featured in in wood magazine. no chip get in the dust collector bags only fine dust.
That's one of the next things on my list to do for sure!!

Robert G. Higgins said:
Justin I bought my bags to replace the original ones on my total shop dust collector from penn state industries. I also built a cyclone that was featured in in wood magazine. no chip get in the dust collector bags only fine dust.
Thanks again Jens, Grizzly is my favorite place anyway!

Jens Jensen said:
http://www.grizzly.com/products/1-1-2-HP-Dust-Collector-with-New-Im...

This is compatible to ours and it is a 19-1/2 inch bag which will do you right Check your ring and see.You can call Grizzley and they will be very happy to serve your needs

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_