Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Working with 1/2" StockI am making a small cabinet for the bathroom using 1/2" stock. The 1" screw exits the first piece of wood off center and comes through th… Started by Helen Bauer |
11 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Kreg, Leigh & FestoolI wanted to use my Festo Mini Vac on the kreg jig but the vac fitting on the kreg was too large so pushed it to one side and did not use th… Started by Jim Carroll |
2 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Pocket Hole Placement: Joinning Aprons to end table legOn an end table I am joining 3/4", 4 1/2" wide aprons to a 1 3/8" square leg. Material is Red Oak. Is it best practice to vertically posi… Started by Azor HomeatShop |
4 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Making repairs with the KregI just purchased a Kreg and have been trying to figure out to break it in, so to speak. Rather than jump in to a huge project I was thinki… Started by Don Clark |
3 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Table Top FasteningThe demo video shows a table top being fastened to an under structure, apparently, without any consideration of wood movement. How does th… Started by Azor HomeatShop |
7 |
Dec 30, 2015 Reply by Elizabeth Leveques |
rabbets and screw lengthI plan on attaching kick plates to the front and back of a TV cabinet I'm building. The sides of the carcase are 3/4" plywood with solid c… Started by Mitchell Wilson |
4 |
Dec 30, 2015 Reply by Elizabeth Leveques |
soft wood splittingI've had to make new cabinet doors for a rental unit. I used vg hemlock for stiles and rails with a 1/8" x 1/4" deep slot for plywood. Whe… Started by Tony DellAqula |
11 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Drawer ConstructionWhat are the options for building drawer boxes using pocket-hole joinery. I've seen pictures of Derek's drawer here: http://kregjig.ning.co… Started by Chris V |
11 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Torque is for headbolts, woodscrews, not so much.The clutch settings on drill drivers are effective at limiting the torque applied to the fastener that you are driving. If that fastener h… Started by Larwyn |
6 |
Dec 30, 2015 Reply by Elizabeth Leveques |
The screwsjust bought the kreg jig late last month. startrd a project and quickly ran out the 10 screws that came with the unit. i live in a smallish… Started by Dave Fisher |
9 |
Dec 30, 2015 Reply by Elizabeth Leveques |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service