Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
drillingWhen I set my drill for the proper width of wood etc I notice the tip if the step drill barely if at all pierces the bottom of the wood. I'… Started by Mike Swaga |
3 |
Dec 30, 2015 Reply by Elizabeth Leveques |
deck 2x2 spindlesI attached deck 2x3 spindles with the kreg blue scres and pocket holes two screws top and bottom. They are very secure. Unfortunately kreg… Started by Joe |
1 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Using Kreg jig instead of a nailer for framingI'm planning to build an office counter using 2x4's as the frame. Can I use the Kreg jig to build the overall frame? Is it an overkill or… Started by Teriyaki |
7 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Introduction & QuestionHI My name is Jim I live in CT and consider my self a moderate woodworker, I have been doing woodworking on and off since my first woo… Started by Jim Lozinski |
9 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Help! Joints not tight!i am a first time user of the kreg jig. tried to drill a few holes with no problem but i had a lot porblem with tightening with the screw.… Started by jc |
6 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Collar DepthI think I'm missing something basic, but I can't seem to find the answer browsing manuals at krieg. I picked up a krieg jig at a garage s… Started by rickm |
4 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Protruding out the sideUsing 3/4" inch stock, with the Kreg Jig set at 3/4", the 1-1/4" screw protrudes out the side. Has anyone else had this problem? Jake Started by Jake Pena |
23 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Kitchen Cabinet DoorsI need some tips for cabinet doors. (how to put them together) Started by Joseph Haynes |
18 |
Dec 30, 2015 Reply by Elizabeth Leveques |
HOW TO USE THE KREG JIG JRSORRY FOR THE CAPS MY COMPUTER IS BEING FUNKY I AM USING THE JIG FOR THE FIRST TIME AND HAVE NEVER CREATED POCKET HOLES BEFORE DOES TH… Started by Richard Neville |
6 |
Dec 30, 2015 Reply by Elizabeth Leveques |
What am I doing wrong?I think there must be something wrong with the way I'm setting up. Can't figure this out.Using the K3, joining 3/4" to 3/4" hardwood.Using… Started by Allen Lindsey |
3 |
Dec 30, 2015 Reply by Elizabeth Leveques |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service