Kreg Owners' Community

Kreg Jig® Operation (279)

Discussions Replies Latest Activity

Screw size for 3/4 inch Setting

A lot of plans I have found say that you shoudl use 1.25 inch Kreg screws for holes drilled at the 3/4 inch setting.  I find that these don…

Started by Andy Harris

7 Apr 21, 2016
Reply by Robert A Edwards

Edge Joining narrow (8.5cm or 3.25") boards with a Kreg R3

Hi there, I'd like to edge join three 1" thick boards that are 8.5cm / 3.25" wide. Initially, when I tried to do this, I realised that the…

Started by Gordon Nicol

5 Apr 3, 2016
Reply by james wilhelm

Screw size for DIFFERENT sized lumber

I seem to recall from a previous post somewhere that when choosing your screw size you should select the screw for the "receiving" piece of…

Started by Steve Gronsky

46 Mar 30, 2016
Reply by Robert

problem with kreg jig

I drilled holes into a piece of 1x3 wood. I had the drill setting right, 1/2,  but had the Kreg jig set too deep, 1 1\2. so I reset the ji…

Started by Mary Murray

16 Mar 24, 2016
Reply by Jay Boutwell

Kreg Mini drilling problem

I recently bought a Kreg Mini Pocket hole. The instructions and videos look pretty straight forward like setting the collar, correct placem…

Started by Beverly

3 Mar 12, 2016
Reply by Troy

Screws keep going through and poking out (frustrated)

I've been trying to set up some butt joints using 23/32 plywood and am very frustrated. I THINK I am following the directions precisely bu…

Started by Richard Sessums

13 Feb 15, 2016
Reply by Pete F

Melamine

I have been told that using melamine for cabinets would be a good choice regarding cost and ease of use - my big question is whether Kreg…

Started by Al

2 Feb 1, 2016
Reply by KregRep

Joining 1/2" to 1/2" with Kreg?

I realise that its considered not ideal to try and join 1/2" wood to 1/2" wood (oak in my case), but I have to make a simple draw carcas an…

Started by Russ

2 Jan 12, 2016
Reply by Russ

Older Kreg Jig - drill bit depth

Can anyone help me with the drill bit depth for 3/4" faceframes for an older jig that does not have the nifty gauge on the top to show the…

Started by John Gates

2 Dec 30, 2015
Reply by Elizabeth Leveques

Need a quick change drill bit

Got a kreg jig jr for Christmas.  Unfortunately my drill is  an impact driver type with a hex type quick change chuck.  Is there a step bit…

Started by Kisukun

3 Dec 30, 2015
Reply by Elizabeth Leveques

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Rip-cut ACS plunge saw

Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Got the original ripcut and didn't really like it had trouble cutting straight. New one has several improvements should make it work much better. especially…Continue

Started by William Burt Brown in General Woodworking Mar 17.

Is the screw driver impact drill rater?

Is the screw driver impact drill rated?Continue

Started by Bob Naylor in Beginners' Zone Mar 10.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_