Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Kitchen Style CabinetRecently I finished a kitchen style cabinet for the garage. I also attached the face frame to the cabinet. As an after thought I want to ad… Started by Chet Zarzycki |
2 |
Jun 27, 2010 Reply by Bruce Rocholl |
Protecting your Kreg BitsI have found this to be the best in the West to keep your point sharp when not using bits snip off some 3/8 clear hose and insirt the bit t… Started by Jens Jensen |
1 |
May 11, 2010 Reply by Terry W. Hawn |
Flower boxes made from composite materialsMy wife wants me to make a couple of window boxes for flowers and I was wondering if anyone has tried to use a Kreg jig on composite boards… Started by ray vile |
7 |
Mar 20, 2010 Reply by Jens Jensen |
Red Oak PlugsI am not terribly new to woodworking...but I am new here.I have the Kreg K3 setup and think it is a nice little system.I have run into a pr… Started by Michael G. |
4 |
Mar 19, 2010 Reply by Jens Jensen |
joining angled piecesI want to join two boards at a 45. I've cut both at 22 1/2 so that they will make a 45. These are 3/4" boards. I've looked at the video's t… Started by Jay Homeyer |
6 |
Mar 12, 2010 Reply by Alan |
Plugs / Caps don't fitHi I made my first Kreg project and built the Student Desk (per Kreg project plan) with birch plywood. Not one of the plugs / caps fit in… Started by Hillary Devere |
10 |
Mar 11, 2010 Reply by Kerry Drake |
Kreg plugs that don't fitI've just started to notice that many of the plugs I try to insert into the pocket holes do not want to slide in freely as they did once. A… Started by Andrew Pensavalle |
28 |
Mar 10, 2010 Reply by AWK |
Stair TreadsI have heard that the Kreg joinery can be used to fasten stair treads to the stringers. Has anyone tried this? The stringers I am working… Started by Glenn Jilek |
0 | Mar 10, 2010 |
Screws popping throughHello all. Let me say upfront that I am a total amateur when it comes to woodworking so my questions may seem naive. I do a lot of DIY pr… Started by Anthony DelleCave |
6 |
Mar 9, 2010 Reply by AWK |
Conversion ChartI found a conversion chart between imperial and metric. It's attached, ready for printing, hope will be helpful. All the best Started by Enrico |
8 |
Mar 2, 2010 Reply by Phillip |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service