Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Pocket hole jig for deck railingHello, I am building a deck from cedar. I used the Kreg Deck Jig to fasten the decking and I'm please with the results. Now I'm just about… Started by John Burke |
4 |
Sep 9, 2011 Reply by John Burke |
Screws not tighteningAbout half the time I drive a screw into a pocket hole, the screw bites in and goes into the material, but doesn't tighten down. It'll fre… Started by Anthony Halsell |
32 |
Sep 6, 2011 Reply by eugene knobloch |
Struggling drill into hardwoodsHas anyone had any problems drilling into hardwoods? I normally build with softer woods and sheet goods but over the weekend I put together… Started by Alex Shiells |
16 |
Sep 3, 2011 Reply by Al Barale |
Simple joineryNew user I'm trying to join 1 x 4 poplar with the jig. I'm using clamps in my shop. I drill 2 3/4 holes in the end piece and everytime the … Started by Jim Buttery |
5 |
Aug 15, 2011 Reply by Jim Buttery |
Tip for making sure your joints / screws are tight and inserting screws in tight placesWhen I first started using the Kreg jig I didn't know what torque setting to set my drill on to get the screw the tightest without tighteni… Started by Steve Berto |
3 |
Aug 4, 2011 Reply by Michael Hritz |
Joint placementI am going to build a bedside table with this sort of design. My question is this: Should connect the outside wood by drilling Kreg holes… Started by Steven Croney |
8 |
Jul 31, 2011 Reply by Alvin Ross Park |
Mounting your jigHello, I just purchased my Kreg Jig. Can some of you experienced users tell me how you mounted your jig? Did you mount it to a bench? Or a… Started by Rex Hoyt |
115 |
Jul 29, 2011 Reply by Ray Romero |
boatsAre any of the Glen L ----boat designs buidable using the Kreg Jig ? Started by Dave G LaPere |
0 | Jun 29, 2011 |
4x4 to 2x6 settingEmbarrassed to ask I need to put a 30 inch post on a deck. I have 4x4 post and decking is 2x6, I'm using 2-1/2 inch screws,but getting t… Started by Jens Jensen |
9 |
May 30, 2011 Reply by Phil Luciani |
Why my pocket holes are not smooth?I used it on plywood. Some pocket hole are very smooth after drill. Some have residuals around the border and I have to tear them off. Any… Started by Will Smith |
2 |
May 28, 2011 Reply by Ken Darga |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service