Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
What setup do I need to attach 2x material to 5/4 material?Most of the guides I've seen for determining the setup for your Kreg jig show equal material. I am building a kids picnic table and want to… Started by Angie Overton |
3 |
Jun 15, 2016 Reply by Angie Overton |
Pocket Hole Jig settings for metric lumberHi. I've actually owned my pocket hole jig for quite some time, but it has had such little use a long time ago that I'm virtually starting… Started by Anony Mouse |
2 |
Jun 5, 2016 Reply by Ken Kortch |
Problem with K5 jigI recently purchased the new K5 jig and read the directions about its proper use. When I attempted to raise the handle and hear the two cli… Started by Lee Warras |
4 |
May 22, 2016 Reply by Glen S |
Screws coming throughI'm building a kitchen table with bread board ends. I built it out of 2x8's cut down to 7" wide and am putting 2x4's underneath as a "stiff… Started by Tim Thomasson |
2 |
May 2, 2016 Reply by KregCS |
Screw size for 3/4 inch SettingA lot of plans I have found say that you shoudl use 1.25 inch Kreg screws for holes drilled at the 3/4 inch setting. I find that these don… Started by Andy Harris |
7 |
Apr 21, 2016 Reply by Robert A Edwards |
Edge Joining narrow (8.5cm or 3.25") boards with a Kreg R3Hi there, I'd like to edge join three 1" thick boards that are 8.5cm / 3.25" wide. Initially, when I tried to do this, I realised that the… Started by Gordon Nicol |
5 |
Apr 3, 2016 Reply by james wilhelm |
problem with kreg jigI drilled holes into a piece of 1x3 wood. I had the drill setting right, 1/2, but had the Kreg jig set too deep, 1 1\2. so I reset the ji… Started by Mary Murray |
16 |
Mar 24, 2016 Reply by Jay Boutwell |
Kreg Mini drilling problemI recently bought a Kreg Mini Pocket hole. The instructions and videos look pretty straight forward like setting the collar, correct placem… Started by Beverly |
3 |
Mar 12, 2016 Reply by Troy |
Screws keep going through and poking out (frustrated)I've been trying to set up some butt joints using 23/32 plywood and am very frustrated. I THINK I am following the directions precisely bu… Started by Richard Sessums |
13 |
Feb 15, 2016 Reply by Pete F |
MelamineI have been told that using melamine for cabinets would be a good choice regarding cost and ease of use - my big question is whether Kreg… Started by Al |
2 |
Feb 1, 2016 Reply by KregRep |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service