Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Tips on working with bamboo?Hi, I just got a bunch of 1" thick bamboo treads and 5/8" thick risers and intend to turn them into basic office furniture (bookshelves, bo… Started by Mischa Machius |
2 |
Jan 4, 2016 Reply by Mischa Machius |
brad nailerWhat is a good inexpensive brad/finish nailer. I've looked at the Stanley TRE550 nail gun and the ryobi nailer/stapler. Really don't have… Started by John Sipsas |
30 |
Jan 4, 2016 Reply by NickM |
Plans and Materials list for DVDsHi, I am new to the Kreg Community and I recently purchased the following DVDs: Cabinet Making DVD and Tables DVD. Is there an area where I… Started by Joe Brennan |
1 |
Jan 3, 2016 Reply by KregRep |
Router questionsI have a craftsman router (315.175340). I want to build a router table. A couple questions. Will my router fit any router plate? Doe th… Started by Brian |
16 |
Dec 30, 2015 Reply by Joe Massena |
Will light sanding a gloss finish result in a satin look?I want to put a satin finsih on a new table top and the varnish is described as a "hard" gloss. Will sanding it with very fine paper result… Started by Gary |
11 |
Dec 30, 2015 Reply by Joe Massena |
staining wood fillerDoes anyone have any good suggestions on how to stain over wood filler in nail holes etc. The filler I use says that it takes stains easily… Started by Fred Odette |
10 |
Dec 30, 2015 Reply by Elizabeth Leveques |
soffit framingHas anyone used the Kreg Jig to frame for a soffit. I am looking for the easiest way to extend an existing soffit in my kitchen by about 6… Started by Laura F |
11 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Here are a few pics of my shopHere are a few pics of my shop. Started by Nlrwilson |
1 |
Dec 30, 2015 Reply by Elizabeth Leveques |
What is your favorite wood to build with?With so many woods available to build projects with it’s difficult to choose. Pine is cheap but very soft, oak is wonderful but expensive!… Started by Ralph Sarc |
10 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Roundover or Beading BitI was taking inventory of my router bits with the intent to start a collection of good quality bits to use in my table and hand held router… Started by kenny from Sundre |
4 |
Dec 30, 2015 Reply by Elizabeth Leveques |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service