Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
90 Degree Corner ClampWhat is the purpose of the round piece cut at an angle that can be rotated and locked at 2 positions? Started by Grant Armstrong |
1 |
Nov 25, 2019 Reply by KregRep |
Exterior Screw for Half Inch MaterialI am looking for exterior pocket screws to use in 1/2 inch plywood and pine/cedar. I can't seem blue coated screws in 3/4 or 1 inch lengths. Started by Jack Corrigan |
1 |
Nov 18, 2019 Reply by KregRep |
Hard time pocketing 2x4Hi all, Fairly new kreg user but have had no issues with past small projects using 1x4, 1x6,etc. Starting a laundry pedestal build that u… Started by Heather Mesa |
3 |
Oct 8, 2019 Reply by Ken Darga |
Piston Support for my Farmhouse cabinetI have built a large Farmhouse cabinet for our kitchen using pocket holes of course. LOL. I used a 48" piano hinge for the 23"x57" door (an… Started by Ed Merrill |
2 |
Oct 5, 2019 Reply by Ed Merrill |
Hanging Project CenterHas anyone found a good solution for hanging the Kreg Project center when it is not in use? Started by EJ Kenney |
0 | Sep 4, 2019 |
Problem with automax project clamp and bench clampI cannot get either clamp to face clamp a 2" x 4". Is there a fix for this? Started by Christian Bookter |
1 |
Aug 9, 2019 Reply by KregRep |
Kreg Jig SettingsNot a pro by any means do I need some advice. Building a shelf using 5/8" shelving (horizontal) and 2' x 2' for support (vertical) I can'… Started by Chip Denton |
2 |
Aug 6, 2019 Reply by Chip Denton |
Using pocket holes on 45 degrees connection for table frameHi all, new member here. I am making a table and for the frame I want to use short braces connecting at 45 degrees to the frame's sides. Th… Started by Zvi Sharon |
2 |
Aug 5, 2019 Reply by Zvi Sharon |
Wheelbarrow organizationAnybody have any ideas on how to make a couple wooden attachments for the side of a wheelbarrow that can hold and secure some long handle y… Started by Vincent A Cutright |
3 |
Jul 26, 2019 Reply by Vincent A Cutright |
Kreg Accu-cutLooking at buying the Kreg Accu-Cut and am interested in hearing feedback. Thanks. Stan Started by Stanley C. Pearse |
0 | Jul 1, 2019 |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service