Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Custom Klamp TableHello, I am am an old woodworker but new to the Kreg way of doing things and would like to build a custom "Klamp Table." I was wondering if… Started by Paqrat |
0 | Jan 21, 2015 |
HardwareHi all. Any suggestions on where to buy decent hardware for the best price? I'm looking for adjustable feet to go under my washer and dryer… Started by Jeff Malmgren |
3 |
Jan 19, 2015 Reply by Ken Darga |
French Cut/Bevel Cut on 2x4's...?Good Morning again Community. I was wondering if it would be advisable to hang my Garage cabinets that I am making using a 45 Degree bevel… Started by Wayne DeVito |
6 |
Jan 19, 2015 Reply by Wayne DeVito |
What screw length to join a 1x with a 2x or a 2x to a 1xWhat screw length would I use to join say a 1x4 to a 2x4 where the pocket holes have to be in the 1x4. Also what length screw to join these… Started by Duane Heda |
2 |
Jan 19, 2015 Reply by Duane Heda |
1" Kreg Screws (Weather-Resistant)I'm building an outdoor table and need some 1" weather-resistant Kreg screws. They obviously do not make them. Does anyone have any suggest… Started by Jeremy Galiano |
4 |
Jan 17, 2015 Reply by Neal Fahey |
ShopNotes merging with Woodsmith magazineLooks like they are going to have ShopNotes become a part of Woodsmith magazine. Anyone else hear this? Started by Gary roofner |
2 |
Jan 16, 2015 Reply by James P. Cottingham |
What wood is the best to use for garage cabinets?Hello everybody. I am new to the Kreg world and was hoping to get a little help in choosing the right kind of wood to make garage cabinets.… Started by Wayne DeVito |
6 |
Jan 15, 2015 Reply by Wayne DeVito |
rough cut tommy mac...lame or what? and some other stuffFirst I will state I miss New Yankee Workshop..even watching repeats gave me insights and refreshed my knowledge base...aided in my design… Started by jefrey smith |
43 |
Jan 12, 2015 Reply by Gary roofner |
Bedside Table PlansHello, I am looking for a set of plans for a bedside table. Would like it to have one or two drawers with a door on the bottom for putting… Started by Blaine Garren |
1 |
Jan 12, 2015 Reply by KregRep |
Kreg HD questionThis is how new I am at this: I was gifted a new Kreg HD kit by my wife on my birthday. Here's my rookie question: Are there special HD s… Started by Jan W. Nahorski |
7 |
Jan 9, 2015 Reply by Ken Darga |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service