Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Project clampI have a project clamp and not the new auto version. Some how, I've loss the adjustment screw for it. Is there a replacement screw or can I… Started by Chuck Webster |
2 |
Apr 21, 2017 Reply by Chuck Webster |
Looking to build a wood box with mitered joints (Kreg Jig 4)Hi Folks Newbie making his 2nd post. I want to build some wood boxes using 3/4" wood. The box will be 8" high, and approximately 18" wide… Started by Jeff Fishman |
7 |
Apr 20, 2017 Reply by Ken Darga |
Kreg 4 jig Newbie - wood splitting problemsHey folks I am an experienced carpenter and do some cabinetry. I just purchased the Kreg 4 jig. I wanted to test the jig by building a… Started by Jeff Fishman |
3 |
Apr 20, 2017 Reply by Jeff Fishman |
Help needed building a pedestal for displaying collectiblesHi everyone, I'm relatively new back into woodworking. I'm would like some help/input on building a would pedestal for displaying some col… Started by Kit Manuel |
0 | Apr 19, 2017 |
New memberHello, name is Brian. Just joined and wanted to say hello. Started by Brian Rowan |
0 | Apr 15, 2017 |
Hello.Hello I'm Jason and in new here and just wanted to say hi. Started by Jason Billheimer |
0 | Apr 15, 2017 |
Black paint finishI've started building a cabinet with poplar. I wish to have a black gloss finish. I'm not an experienced "finisher". I don't see much i… Started by Bill Bianco |
8 |
Apr 14, 2017 Reply by Kirby Bradley |
Kitchen Cabinet Face FramesI am building Cabinets with Pocket Screws. Using 3/4 oak Plywood and 25/32 face frame. I want to flush route and round over the face frame… Started by Robert Marshall |
3 |
Apr 12, 2017 Reply by Jay Boutwell |
Which do I want, a jointer or planer?What works best at making nice crisp 90 degree edges on lumber that are exposed??? Started by Bill Jones |
6 |
Apr 11, 2017 Reply by michael evans |
Pocket Hole FailureI have always heard pocket holes are amazing. I cannot seem to figure it out. Everytime I try making something, the joints never pull snu… Started by Jon Andis |
8 |
Apr 6, 2017 Reply by Mike |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service