Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Contrasting Hole PlugsI am making some oak furniture and on some sides the pocket holes will be visible. I don't really mind this at all because I want to use a… Started by Andrew James Kavanaugh |
10 |
Jun 17, 2011 Reply by Andrew James Kavanaugh |
Gun Cabinet PlansDoes anyone have a gun cabinet set of plans? Stand up hold 4 to 5 long guns. Started by Bob Myers |
2 |
Jun 14, 2011 Reply by Jens Jensen |
Screw Length 2x4s at right angleThis is my first project with the jig. I am making a frame with 2x4s joining them at right angles. Since they are both 1 1/2 thick I set t… Started by Larry Mathews |
2 |
Jun 13, 2011 Reply by Larry Mathews |
wobbly shelvesHello, My son and I purchased the Kreg master system to build some bookcases for his room (with hopes of using the Kreg in future projects… Started by Keri |
34 |
Jun 9, 2011 Reply by Ken Darga |
Joining 2" thick material to a 5x5 piece..helpCan i use my kreg jig, if so what size screw? local stores only carry up to a 1 1/2 screw for this...will that work?? this is for a mons… Started by MJB |
3 |
Jun 2, 2011 Reply by Bob S |
SplittingI am Rex. When I try to join two pieces of 13/16" cherry wood, the receiving piece splits. I am using 1 and 1/4" fine thread screws. Can… Started by Rex Earl |
2 |
Jun 2, 2011 Reply by Rex Earl |
Fastening Deck Boards to Joists - Weakening Joists?So I've already attached a few deck boards by drilling pocket holes into the joists and securing with weather resistant screws. It strikes… Started by Dave Bless |
1 |
Jun 2, 2011 Reply by John Schaben |
Router helpI have a new hitachi router but i have a question. I have a 3/8's round over bit that i cant get high enough into the base for it to work c… Started by Steve Bennett |
9 |
Jun 2, 2011 Reply by Steve Bennett |
Crown JigHas anyone used the Kreg Crown Jig? And if so, how did it work? Started by Roy Orosco |
1 |
May 30, 2011 Reply by Phil Shull |
Deck jigBasically my question is a simple one....can you use the deck jig without using spacers between the boards? I'm in the process of buildin… Started by Ron Weeks |
5 |
May 26, 2011 Reply by John Schaben |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service