Kreg Owners' Community

Hello All. 

First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then of course) stripping out? I suspect technique may be contributing, but I also wish they were perhaps a bit deeper and harder. Anyone else have this problem or abe to offer any suggestions? 

Thanks in advance. 

Views: 1507

Reply to This

Replies to This Discussion

Mine rounded off quite quickly, as well.  I attributed it to using an impact driver to drive the screws, some of which had space restrictions and required awkward angles.  I did pick up a couple at Rockler that had hardened tips and lasted quite a bit longer.

Thanks, Tim. The only ones I see at Rockler, however, are labelled: Kreg Jig® HD Driver Item #: 47983. Are they the ones you ordered?

Mr. Hampton, 

When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your chance of stripping out.  We do not recommend using an impact driver when putting in your screws as this makes it easy to over drive the screws and increase your chance of stripping out as well.  While driving your screw you will want to make sure you are going at a consistent speed allowing the screw to do its work.  

The HD driver you are referring to on the Rockler page you found would not be the correct driver.  This is for our HD jig and is actually a #3 driver instead of the normal #2.  It would be too large to fit into the head of our normal screws.  If you have any other questions please let us know.  

Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back.

Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just doing that helped me a lot.

Thanks, KregCS. I do try to let the screw do the work. Since you can't see the screw head and you driving at an angle, it is a bit more of a challenge to align properly. Will try harder, but will also get hardened tips. I am sure I'll improve over time. 



KregCS said:

Mr. Hampton, 

When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your chance of stripping out.  We do not recommend using an impact driver when putting in your screws as this makes it easy to over drive the screws and increase your chance of stripping out as well.  While driving your screw you will want to make sure you are going at a consistent speed allowing the screw to do its work.  

The HD driver you are referring to on the Rockler page you found would not be the correct driver.  This is for our HD jig and is actually a #3 driver instead of the normal #2.  It would be too large to fit into the head of our normal screws.  If you have any other questions please let us know.  

Thanks, Glen. Will pick some up and try them. Thanks for the drill position tip. Will try it next time I am using the jig. 


Glen S said:

Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back.

Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just doing that helped me a lot.

You're Welcome. I hope that trick works for you. I also bought some screw wax that I'm going to try on a Tiger Maple face frame.

The screw wax made driving the screws a whole lot easier!

EM, aloha~

I too am a newcomer to the system and I'm finding the same problem. I am using a drill (not impact) with the clutch set low and, despite really pressing to get the tip into the screw (and feeling it lock in), I still get some spin-outs and eventually stripping of the tip. I was able to extend the life of one tip by carefully grinding the very end off, but only once....it seems that the square profile tapers out as it goes up so unless I can also file/grind the square slightly, I'm having to get new/spare tips.

Part of the problem may be that I've been working with 2.5" screws, deep in the pocket and going into teak...

I did find, as Glen S. below says, turning the drill upside down seems to provide more control.

Thanks to everyone for sharing their knowledge and experience!

Sorry for the delay in response.  The ones I picked up at Rockler were in the store and aren't shown on-line.

I would LOVE to have Star heads screws instead. Not a big fan of square bit...

Me too!

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_