Kreg Owners' Community

Hello,

I have just started using the Kreg jig which I think is great but I have been having difficulty lining up the driver bit with the screw head once the screw is in the pocket hole.  It seems to be a more fiddly than Philips head screws.

Is it just me (Its quite possible it is!).

Cheers,


Andrew

Views: 1075

Reply to This

Replies to This Discussion

Position the driver bit to the screw head---

slowly rotate the bit, until it seats into the recess of the screw head---

this can be accomplished by "feel", (you're working in a "blind hole")---

then proceed to drive the screw in, until it bottoms out---the joint closes and the correct torque is achieved.

"Proceed slowly" while driving in the screw.

When you achieve a snug fit---stop---then slowly rotate a 1/4 turn at a time.

DO NOT over-torque---"strip-out" can occur.

if the pocket holes are facing up and you can see down into the hole I suggest you place the screw onto the magnetic bit and guild it in until you get a feel for the angle of the screw and hole, it doesn't take long, maybe a dozen screws like that, Also I have a drill with torque settings, I find it a must to have to eliminate the chance of striping out the screw joins, mine is set to about 1/4, after everything is together I bump up the torque a couple of clicks to snug the screws down a little more.

If you watch some of the Kreg videos you might note - as Richard said previously - that they put the screw on the bit before inserting the screw into the pocket hole.

Also, as Richard also suggested, run light on the torque to avoid stripping out the screw. If using a drill driver you may want to set it's clutch to the lowest torque to begin and then increase the torque stepwise until you feel the screw is seting correctly - maybe even checking it with a hand screwdriver to be sure.

Thanks for the replies.  Its mainly when unscrewing, I have a drill driver with adjustable torque and have been adjusting, but quite a few times I have had to peer down the hole to see which way the screw head was pointing and then carefully slide the drill bit in to line up.  Its not a big problem, but it is a tad annoying!  Im more used to the Philips head screws, so maybe it will become easier with more practice.

Thanks again.

Nufcac, 

Some Kreg screws feature a "square" and "cross-point" recessed head.

it all comes down to practice, you'll get the feel for after an easy project.

Sometimes a torch helps especially if you have one on the drill .

Mick,

Please define the "torch" you speak of.

Would this be "Propane/Map" or "natural gas" ?

michael evans said:

Sometimes a torch helps especially if you have one on the drill .

Yes I have a torch on the drill, I think I am starting to get a hang of it though, I've been building stuff like crazy the last few days, which is good for reducing furniture costs for my new house, as well as stocking up my fire wood pile but not so much for the neighbours!

This is a great drill by the way:-

Makita DHP459RMW 18V 4.0Ah Li-Ion Cordless Combi Drill LXT Brushless Motor

In the U.K. the term "torch" is used the same as the term "flashlight" in the U.S.

Ken Darga said:

Mick,

Please define the "torch" you speak of.

Would this be "Propane/Map" or "natural gas" ?

michael evans said:

Sometimes a torch helps especially if you have one on the drill .

Define torch for you fellas across the pond , a flashlight is called a torch here in the U.K. no naked flame usually battery powered . Looking where to place a pocket hole drill bit could be a bit interesting using a naked flame ha.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_