Kreg Owners' Community

Make your own shop-made clamping & assembly workbench.

........

Kreg Klamp Track

locate several of these units, banked side-by-side, to the desired depth of your top.

Make a work-top base from 3/4" MDF, or the like, to a width and depth, as applicable.

Fasten the tracks to the base.

Secure the assembled components to work-stand.

This concept will permit nearly limitless clamping opportunities.

Views: 2771

Reply to This

Replies to This Discussion

What is the best width and length for furniture like dressers, night stands & beds?

A 4ft by 3ft table size will suffice nicely, for most uses.

Thank you for your advice. Kevin


Klamp trak Worktop Option(s):

NOTE: each Klamp Trak is 33-3/4" long x 2-1/4" wide x 11/16" thick.

OPTION(S):

A)  Make a sub-base 33-3/4" long, the same length as the Klamp Trak.

For a base depth of 22.50", 10 tracks are needed, when banked side-by-side.

B)  For a base depth of 47.25", 21 tracks are needed, when banked side-by-side.

C)  install 11/16" thick spacers, "X" inches wide---and locate between each track.  

Installing spacers between traks, will reduce the quantity of traks needed for a worktop.

D)  Two tracks, at 90 degrees to each other. One located along one edge of the sub-base, and another at 90 degrees.    Sub-base of 36" x 36".

                             Diagram "A"

  1)  three traks---sub-base of 36" x 38-1/4"

  2)  four such traks---sub-base of 38-1/4 x 38-1/4.

E) Multiple traks for a larger worktop

                                         Diagram "B"

Note:

There are nearly limitless design possibilities.

The Traks can be butted, end-to-end, or cut to a desired length, to suit.

Suggest draw-out the design options you'd like, and/or make a scale model, so as to give a visual of the desired worktop.

Can T Tracks be used in this set up and be accurate. I own peachtree types for miter gages and they attach with wood screws. What type of clamping system is acceptable also for precision type work?

Kevin,

"T-tracks" are generally made of thinner material---

held by small screws---

suitable for light duty clamping pressures.

T-tracks can permanently deform when exposed to heavy clamping pressures.

The Kreg Klamp Trak, is intended to be secured to the sub-base with bolts and nuts, on 2" centers,

which will provide for heavy pressure clamping.

Simple "C", "F", "pipe" or "bar" clamps can be used for clamping.

It's how these type clamps are used that will provide the desired end result.

For clamping larger pieces, a pipe or bar clamp may be needed.

"F" clamps for small to med size pieces, with light to med clamping pressures.

"C" clamps are available in a variety of sizes.  

For light clamping to heavy clamping pressures.

"Web" or belt type clamps are also available, and suitable for clamping square, rectangular and round type structures.

For many applications, auxiliary devices may be needed,

such as a "pad" under a clamp face to prevent marring or distortion of the work-piece surface.

"Precision type work" can be accomplished with suitable skills and tools for the end product result.

Thank you for you advice. Kevin

Hi everyone, new to the community and have a few questions and this happens to be one of them.  We plan on building our own kitchen cabinets and I was a bit confused on building a clamping table, like what I need and deciding how big I need it to be. 

I think the confusion for me is how many tracks I would need and why the need for 10 tracks side by side?  I am confused, sorry.

I have a project we are working on now and will post the questions I have about it on another thread but I am eager to learn about Kreg and all the many uses of it.

I would use 2 tracks, forming a 90 degree angle. Doing it yourself might be fun, but for the money, you cant beat one that's ready to go. https://www.kregtool.com/store/c30/klamp-tablestrade/p68/klamp-tabl...

Hi Suzy, I have been building cabinets professionally for about 27 years now and have never used a clamping table other than a sturdy and sound 4 ft wide by 8 ft long work bench.   I have build many large cabinets as big as 5 wide x 3 feet deep by 8 feet tall and found the bench more that enough to build rapidly and accurate cabinet boxes.  The bench must be level and this helps keep the cabinet panels flat and square.  Anything I needed to clamp I used jigs of which I clamped to this bench

A clamping table would be something that I might use when building face frames and such where there are many pieces to attach together.  What I did for this is to have a grid of 2 x4 on edge which picked up the face frame pieces to enable a clamping of a face frame clamp. 

I have considered a face frame clamping table made by Kreg Tools and think it is a good system but I do not have the room for something like this.  For any glue up panels I use standard clamps laying flat on the bench top.  The flat bench top will keep the panels flat.  I normally use wax paper under the joints and on some occasions I will use newspaper and when the glue dries I scrape it off with a scrapper along with any glue.  Any questions I will be happen answer them.  Also welcome to the community.

Thank you both, Thomas and Jay.  I appreciate your responses to my question.

OK, so how do I attach the rails?  Directly on top of the plywood base?  I am thinking of making it about 3'x4' sized.

Jay, it sounds like you make some real nice cabinets.  I can only hope our projects turn out well

Thanks again.

Suzy, If you are going to build a small table for clamping I would inset the "T" Track Rails into the plywood so that the top of the rails is flush with the surface of the plywood.  This would give you a flat surface in which you can easily move your project about on the table and position them for clamping. 

 It is easier to use a router and bit guided by a fence than it is a table saw but either can be used.  Use a dado blade in the table saw or a dado cutting router bit in a router and take several shallow passes with the router until you have cut the dado to the correct depth.

If you take your time with the cabinet building I am sure they will turn out great. 
 
Suzy said:

Thank you both, Thomas and Jay.  I appreciate your responses to my question.

OK, so how do I attach the rails?  Directly on top of the plywood base?  I am thinking of making it about 3'x4' sized.

Jay, it sounds like you make some real nice cabinets.  I can only hope our projects turn out well

Thanks again.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_