Kreg Owners' Community

Hi All,

I'm finishing a bathroom project with a fiberglass shower.  I have a 18" opening around the top of the shower.  I bought cement backer board to cover the opening.  I'm not planning to tile the opening - probably just a couple coats of latex/waterproof paint.  Is Durock backer board correct or should I use another type of cement drywall?

Thanks,

-Brian

Views: 621

Reply to This

Replies to This Discussion

Durock is good.  Prime and paint with mildewcide like Zinsser bath paint, and then use exterior caulk the top of the shower.  Don't use drywall screws.  HardiBacker is also good.

Don't try to use pocket screws on it.  ;-)

Rick,

Do you have, or know of, a suitable screw for affixing the boards you described?

Thanks.

I found some at Lowes called Backer-On.  They come in a couple counts depending on your needs.

Here's a pic of the screws Brian referred to.  They are square drive. 

The screws are supposed to c'sink themselves using the ribs on the underside, but even with my Makita impact driver, they would strip or break before burying themselves flush in the Hardiboard.

IIRC, with most of the screws I had to remove them, c'sink the hole with a c'sink bit, and then re-screw them flush. 

Don't try these in pocket holes.  ;-)

Ken Darga said:

Rick,

Do you have, or know of, a suitable screw for affixing the boards you described?

Thanks.

Thanks Rick,

The "square drive" is the feature in the head---

which dictates the type and size of driver bit to install/remove the screws.

The "type of screw", which is the style and thread-pitch, is the main factor for use in such material.

The threads in your photo, appear to be akin to fine-theard drywall screws.

I've found that some products are identical in nature, except repackaged a "specific" purpose.

The next trip to Lowes, I'll peruse the screws.

Perhaps a "trim" screw would suffice nicely.

Trim head screws have a smaller diameter/size head---

permits recessing without countersinking---

with little to no distortion in the workpiece surface---

prevent splitting.  

(the screws will split the workpiece, if installed near an edge/end, without drilling a pilot hole and countersinking.  (The OEM's claim they won't split---yah right.  When i've brought it to their attention, they don't respond).

Dry wall screws feature a "bugle" head, which can split delicate wood or when installed close to the edge/end of a workpiece.  These heads will require a "countersinking" operation before installing, so as to avoid distortion/splitting, or the like.



Rick said:

Here's a pic of the screws Brian referred to.  They are square drive.  .../p>

I used Hardibacker panels under Swanstone solid surface panels which make one of the nicest showers around -- you can scrub it with brillo pads and no grout lines.  The screws are course thread 0.195 in diam., but definitely not brittle like drywall screws, which are case hardened.  Neither will these screws rust, since they have to survive in a shower.

Since the backer board is so hard, deriving its hardness from silica sand, even the scoring ribs under the screw head could not c'sink the screw.  The screw is countersunk so that tile, solid surface panels, or fiberglass panels can lie flat.  

Trim head screws are also very brittle, and tend to break in anything harder than pine.


Ken Darga said:

Dry wall screws feature a "bugle" head, which can split delicate wood or when installed close to the edge/end of a workpiece.  These heads will require a "countersinking" operation before installing, so as to avoid distortion/splitting, or the like.

Thanks Rick.

I'll keep that in mind when I do a new shower/tub install.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_