Kreg Owners' Community

I'm new to Kreg pocket hole fastening and I'm trying to build a simple 90 deg. butt jointed frame with 1/2" thick white oak.

When I join the frame using the recommended 1" long fine thread screws there is a noticeable bulge on the face of the frame where the screws have set. It appears that the screws are much too close below the finished face of the frame.

I've rechecked all the settings for the 1/2" material and seem to have it right.

Any suggestions on what to do?

Views: 1050

Reply to This

Replies to This Discussion

Well are you useing a Microjig and if so you'll have to use two nickle's and a dime to set your stop callor and go slowset your drill at 7 or 8 . oh some pic's would help on projects like this so poeple can help you batter.

Yes, a picture of where it is bulging would be helpful. You can post it directly into this discussion, or in your gallery and let us know it's there. If I understand correctly where you are getting the bulge, you may have over driven the screws in. For driving the screws are you using a drill or a driver with a clutch?

Onno

John, 

By what you've described, or I understand what you've written---

the screw has gone too far---

nearly exiting the back side of your work piece---

which has resulted in the ''bulge''.

Back off on the drill stop (shorten the drilling depth).

Recheck your settings, then recheck them again---akin to measuring twice and cutting once.

Also, read the instruction manual a couple-three times, become totally familiar with the tools,

make practice pieces, before proceeding to the final build.

John,

 

I was curious if your material is a true 1/2" thick.  If it is a little bit undersized it can change the placement of the screw causing it to almost come through like you are referring to.  The best solution is to either adjust your depth collar a little bit or you can try using our 3/4" screws for this application. 

John all the members below are correct in what they are saying.  Usually the bulge in the wood is the end of the screw being very close to the surface.  In addition to this something I have found in all the years that I have been driving screws is that sometimes if you are not careful the screw does not follow the direct line of the pilot hole and will take a course of travel out of the pilot hole that runs it near the surface.  This is because the screws are very good at cutting their own path and just a little bit of a angle of the driver will allow the screw to bore out of the pilot hole and cut its own direction towards the surface.  In this case it is usually tipping the driver to far upwards and pointing the screw down towards the outer surface of the receiving piece. 

What I am trying to say is that the screw enters the pilot hole and because of the driver angle will bore out of the side of the pilot hole and cuts its own thread in a wrong angle resulting it the screw coming very close to the surface making the bulge.

Jay,

The air nailers are notorious for the fastener exiting the finished side of a work-piece.

A nail/brad/staple, when following the grain, can exit the work-piece.



Yes they are and that is a reason I try to use nails that is cut like a chisel and shoot the nail across the grain. This  forces the nail to cut the grain rather that seperating the grain.  This seems to help trememdously when using nail brads.  When I do this I seldom will get a nail through the wrong side of the material.

Ken Darga said:

Jay,

The air nailers are notorious for the fastener exiting the finished side of a work-piece.

A nail/brad/staple, when following the grain, can exit the work-piece.



David isnt two dimes same as two nickles and a dime



David Dean said:

Well are you useing a Microjig and if so you'll have to use two nickle's and a dime to set your stop callor and go slowset your drill at 7 or 8 . oh some pic's would help on projects like this so poeple can help you batter.

no the two dime's are thicker but that was the only way to stop blowing out my egde's and and going thow the other side what Kreg hasnt said but the pan head scerws will suck down in to the seacnd hole if you dont be careful it's not hardwood you are working with.

Jens Jensen said:

David isnt two dimes same as two nickles and a dime



David Dean said:

Well are you useing a Microjig and if so you'll have to use two nickle's and a dime to set your stop callor and go slowset your drill at 7 or 8 . oh some pic's would help on projects like this so poeple can help you batter.

The washerless screw heads

Fine thread pocket hole screw photo 

will penetrate beyond the bottom of the hole, in ''soft woods''.

During installation in soft woods, use a ''low torque''.

This low torque style/type power tool, primarily used for small fasteners. 

FREE SHIPPING — Milwaukee Cordless Screwdriver — 2.4 Volt, 400 RPM, 26in.-Lbs. Torque, 1/4in. Drive Size, Model# 6546-6 

or a small ratcheting screwdriver

,      ,  

or the like.

Many thanks to everyone who's responded to my question.

I'm going to give it another try this weekend and I'll let you know the outcome.

This blog is great for beginners like me.

John

John, you are pushing the lower limits of pocket hole technology.  1/2" wood (which is really 7/16" or 12 mm) is difficult to do well.  I did a lot of experimenting, and gave up on it.  What did work for me nicely (building large drawer boxes) was going thru 1/2" ply into 3/4" ply.  It turned out to be a good compromise.

John Ekholm said:

Many thanks to everyone who's responded to my question.

I'm going to give it another try this weekend and I'll let you know the outcome.

This blog is great for beginners like me.

John

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_