Kreg Owners' Community

I have been interested in getting and using an overarm router system. There seems to be very little interest today by woodworkers in a good afordable overarm or overhead router. I don't understand why most router users seem to prefer working blind with a regular router table or freehand routing, when you can use an overhead router system and see what you are doing. A few years ago Sears Craftsman put out a nice unit, and several other machine companys did also, but that seems to be a thing of the past. Does anyone know of anyone building such a unit today?  I am posting a picture of the Craftsman unit that I spoke about. It is shown on the front of a book.

Lowell

 

Views: 6201

Attachments:

Reply to This

Replies to This Discussion

These are what are known as pin routers shopsmith may still make a pin router here is a link.

http://www.shopsmith.com/academy/routing2/index.htm

I'm guessing its fear of fingers getting mixed up with the router bit ... kind of like the move away from radial arm saws.  Putting the bit on the bottom allows the wood to act as a sort of guard - so long as its movement is controlled (proper feeding, fingerboards, ...).

... but I'm NO expert ... just a beginner myself

Hello Lowell,

I investigated the same principle after not being able to afford a decent sized CNC Machine.

The only one I found was called a Torque Workcenter, and they come as a fixed O/H router or a more sophisticated mobile unit.

Both were also expensive for my home workshop conditions so I never followed up on them..

Regards

Robert Brennan

Hi Lowell, I use a pin router frequently when I am cutting design engravings into cabinet doors, drawers, and rail & stiles and other projects.  I use it with spiral upcut bits for doing design cutting that is almost impossible to cut of needed verticle depth of cuts into wood using a hand held or dremel tooling.  I fine it works well.  I also use it with the router mounted under the table for cutting flush cuts against a templet when making the arched rails of cabinet doors.  The one I have is a shop smith and I mount different mid sized porter cable routers in it.

The attached picture is with the arm moved to the right of center of the table.  Normally I have a router in the upper arm however I have removed it to use on a job site where I needed this router.  There is one mounted under the table and when I have one in the upper arm and need to use it as a pin router I just remove the bit from the table mounter router and insert a cover plate over the hole, move the pin router arm over the table and start cutting.  Excellent tooling to have.

Hi, All:

 Jay, what kind of machine is the one that you show in the picture that you posted? Would it hold a porter Cable

laminate router like the 310M that I have? It looks like a nice set up. I am about to give up and try to build one.

I built and used an over pin router set up, but, you still are routing blind.

Thanks.

Lowell

Lowell it is one made by shopsmith and was made about 25 years or so ago.  It holds the mid sized routers and does have some hard rubber adapter made like a pad that allows you to use the small router like laminate routers.  I never have put one in it as I have found the larger router to be all I need and also gives me the ability to use a 1/2" dia shanked bits.  When I mount a router in the top I can either remove the lower router or just remove the bit and place a cover over the hole.  The way you see it now it has a router under the table with a flush trim bit protruding.  I use it for flush trimming the arched rails with the templet and also the arched panel as the step just before cutting the pattern in the arched rail and the arch on the panel before cutting the raised panels.
 
Lowell D Sites said:

Hi, All:

 Jay, what kind of machine is the one that you show in the picture that you posted? Would it hold a porter Cable

laminate router like the 310M that I have? It looks like a nice set up. I am about to give up and try to build one.

I built and used an over pin router set up, but, you still are routing blind.

Thanks.

Lowell

I have the Shopsmith overhead pin router table if anyone is interested in buying.  I live in Atlanta Ga area.

Hi, Cindy:

I live in Central Ohio and wonder if the shipping costs would be prohibitive? does this include a table? How much does it all weigh? What are you wanting to get for it?

Thanks,

Lowell

I am not sure. It is pretty heavy so I would imagine the shipping would be bad.

 Yes it does have a table.  It does not include a router.  We used a porter Cable router in it when it was used.

I am not sure how much it is worth at the moment. I haven't used it in a number of years since I lost my husband.  I will see if I can come up with a price or do you have an offer if you are interested? 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_