Kreg Owners' Community

Oops, I set the jig and the drill collar wrong and drilled 2 holes clean through the wood and right through the blue plastic. I can see the clamp rods through the holes but the drill stopped just short of them. Any ideas about how to plug the holes to keep sawdust out or do you think it won't bother anything down the road if I just leave them as-is? I don't want to put any glue in the holes since it might drip in and effect the clamp operation. And, I can't just tape over them since that would cover the embossed numerals and lines in that area.  Thanks for your advice.   Joel

Views: 1639

Reply to This

Replies to This Discussion

Maybe some oversized rivets might plug the hole.

''BONDO"...


''schalks wood putty''...

Great ideas. The vac sounds like the simplest place to start. Thanks everyone for your suggestions. 

A good set up tool and a reminder to set stop corectly.    I lay a dime on the jig and let the drill rest on it.  This gives you a perfect little dimple hole on the end of board everytime. 

I just did this last week, i almost wanted to cry, but it still works fine and mistakes is how you learn.  I'm going to try the dime trick.

Perhaps a half dollar is better.  I read that those "dimples" were not such a good thing since they could hold the boards apart.

I think using a spacer is easier for lining up the collar anyways.

I don't understand the discussion about the dime/half dollar/dimples. Exactly where do you "lay a dime" and why?

Joel, using the K3 or K4 with the drill guide set for your wood thickness, insert the drill into one of the guide holes.  (No wood clamped in place.)  Loosen the lock collar. The drill will bottom out on the Kreg jig base.  Slide coin or spacer under the end of the drill to lift it off the base.  Tighten lock collar.  You are now set up to drill!

Thanks Rick. What is the benefit to this "spacer" idea over using the standard Kreg approach? Is this just more foolproof, or does it improve the joinery? I'm new to pocket holes and I'm anxious to learn. Thanks for your explanation. 

  Joel   It is just a little trick taught to users to help them from doing what you did.  :) 

Like Edward said, and it seems easier to adjust the locking collar this way.  Sometimes it just makes the adjustment more understandable, and then "fine-tunings" for unique combinations are more foolproof.

The goal is for the drill not to push the wood out -- the dimple -- because then the two boards might not seal up tight.  Either method is fine, and accomplishes the same thing.

I encourage you to get a bunch of screws and try different combinations of wood.  Try it with and without glue.  Try to bust the joints apart, and see how strong they are.  That's the best way to become proficient.

joel adler said:

Thanks Rick. What is the benefit to this "spacer" idea over using the standard Kreg approach? Is this just more foolproof, or does it improve the joinery? I'm new to pocket holes and I'm anxious to learn. Thanks for your explanation. 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_