Tags:
Depends on which table/plate combinations you get. Rockler sells a plate predrilled for the vc. Their plates are 8-1/4 x 11-3/4 which fits the Rockler and, I think, the Benchdog tables. Woodhaven sells 9 -1/4 x 11-3/4 plates which they will drill for the vc for $15. The third most used size plate is 9 x12 which is sold by MLCS, Peachtree and others but I don't know of any predrilled for the vc. Some of the bigger vendors may do it for you at an additional charge. You would need to contact whoever directly about that service.
On a side note, I have the 2 base kit version of the vc and it would not be my first choice as a table router. I like it a lot for hand work though.
Think seriously about getting a router raiser with its own router motor. Being able to change bits and adjust bit height from the top of the table will save a lot of time. I have a Bench Dog Pro. Expensive, but I am sure glad I spend the money. (My wife gave me a $100 gift certificate that ended up costing me $800 with the router lift, Rockler table, Incra fence adjuster, and router motor.)
If the router raiser isn't in your budget right now, be sure to put it on your Christmas wish list.
Of course, for $250 you can get a router with a built in lift
http://www.amazon.com/Triton-MOF001C-4-Horsepower-Precision-Router/...
Depends on which table/plate combinations you get. Rockler sells a plate predrilled for the vc. Their plates are 8-1/4 x 11-3/4 which fits the Rockler and, I think, the Benchdog tables. Woodhaven sells 9 -1/4 x 11-3/4 plates which they will drill for the vc for $15. The third most used size plate is 9 x12 which is sold by MLCS, Peachtree and others but I don't know of any predrilled for the vc. Some of the bigger vendors may do it for you at an additional charge. You would need to contact whoever directly about that service.
On a side note, I have the 2 base kit version of the vc and it would not be my first choice as a table router. I like it a lot for hand work though.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service