Kreg Owners' Community

I am building a small coffee table and am looking for ideas to keep the table top flush while I join the pieces together with pocket screws.  The top is a 2x4, 2x6, 2x4 with a 2x4 apron.  Also, how far should I space the pocket screws.  The top is 36-inches long.  Thanks, Bill.

Views: 557

Reply to This

Replies to This Discussion

If you are talking about the boards for the top I would just use the same clamps you use to glue up a top. I use what ever looks good to me but 6" or so should work for spacing

I would space the screws 8 - 12 inches apart, work one joint at a time starting at  one end  and work to the other end, clamp the pieces in place lightly, use a hammer or mallet to fine tune the alignment then tighten the clamps and drive the screws, repeat at next screw location, I have also used biscuits to align the parts on very large glue ups

Permalink Reply by Jay Boutwell 13 hours agoDelete

Bill, an old trick that I use often when I am gluing something such as an edge band or even adding onto a pre-existing flat piece where I am working upside down and want to be assured that I do not have the pre-existing surface to be higher than what I am adding onto is to use some common cardboard strips that are about 1/32" thick.  You will need a flat surface of which to work off of.

Lay the strips on the pre-existing area so that it raises the surface upward (strips on the face of the table top and the table top is not laying upside down so that the back is facing you,)  It is always best to begin this task with the edges free of glue and place it into position.  Run is a pocket screw of which has given you a location where the pieces will not slip.  Remove the screw and add glue and reattach.  Add the screws until you have added all for this piece and then repeat for each separate piece of added material.  What the paper has done for you is given you a way to insure that the existing piece is not higher than the piece you have added onto.

It is far better to have the added pieces higher that the other main surface as you can work these down using sandpaper and or better yet a cabinet scrapper.  If it was the other way around then you would either have to live with it or sand down the full top to fit the edges.  

The thing you have to watch for here is for the card stock must not come into contact with the  pieces you are adding or it will act in the reverse.  Multiple pieces of news paper will also work.

As for screws I drill about every 5 to 6 inches apart.

Thanks for all the tips.  The coffee table top had one piece that was slight below the apron, about an eight of an inch.  I'll use all the tips when I make the small end tables to match. 

Thanks,  Bill

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_