Kreg Owners' Community

I recently purchased the Rip Guide and have used it for 4 or 5  8 ' long rip cuts on plywood and MDF. I am somewhat disappointed with the quality of the tool.The fence which is plastic is not square to the guide bar. The anchors that clamp the base to your saw does not hold well because it is mounted again to plastic so when you tighten the the mounting brackets it begins to bend the mounting plate. Overall if I were in the market for another guide I would not purchase the Kreg Rip Guide. They should stay with metal fixtures as they originally had on so many of their earlier tools.

Views: 528

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by John Ibbotson on October 6, 2014 at 4:55pm

I agree 100% with Clay, the tool doesn't list the saws it is compatible or incompatible with and so I ended up wasting money on an item that doesn't work for my Dewalt cordless or my Skill corded circular saws.  These are two major brands that I would have expected the Rip Cut to work with.

Comment by Clay Richardson on August 17, 2014 at 1:33pm

  I own quite a few Kreg tools and most of them are pretty good.  Kreg should refund the money to anyone who purchase this worthless piece of crap.  First you have to have a saw that fits.  And then try ripping any over a few inches and you are asking for kick back. 

  Mine is sitting on the shelf covered in dust. 

Comment by Zachary on March 17, 2014 at 10:07am
I've used it and its not bad. A zero tolerance plate for the saw would be better.
Comment by George Graham on February 12, 2014 at 3:54pm

Thanks for the advice, I was going to buy one as they look very impressive and I'm

a novice so will hold off until I get some positive feedback.

Comment by Nicholas W. Kostella, Jr on January 29, 2014 at 11:11pm

DANIEL, I purchased the Rip Guide as well...I have found that if you cut slow that it works okay. Oh yeah, double check the measurement setting too.

Comment by KregRep on January 17, 2014 at 4:32pm

Daniel,

Sorry to hear of the issues you are having with your Kreg Rip-Cut.  Please get in contact with our Customer Service Department at your earliest convenience; they will be happy to assist you.

You may contact them by phone at 800-447-8638, or online at http://www.kregtool.com/Customer-Service-Serve.html.

Thank you for your interest in Kreg products!
KregRep

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Missing clamping table project 3 Replies

Started by Brandon B. in Beginners' Zone. Last reply by jock sloan 7 hours ago.

90 gallon aquarium stand

Started by Glenn Gilbert in Community-Specific Jun 11.

Proper clamping technique 1 Reply

Started by Ron Salgado in Kreg Jig® Operation. Last reply by KregRep May 31.

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff May 20.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_