Hey everyone, just wanted to know if anyone else has had problems with their precision router table. I,ve have had two, the first is the fence do not line up with each other, soft wood its not to bad, ( like pine) but hard wood I have to pull the piece from the fence to clear the other one , and we all know what happens there. the second is the bracket that holds the fence to the table. is comes lose, I,ve tighten the screws so many times that they have become strip. I,ve been woodworking since 94, so I,ve done all the little tricks to fix my fence, but it still works its way lose. I have gone kregs web site with my complaint, but no response from them. this has to be one the best router table out there, anyway thanks for listening, keep makin saw dust.
Comment
Happy to report when I emailed Kreg about my problem they immediately shipped out two replacement fence faces. Within 2 days I had them at my front door. I didn't think it would fix the problem, but I installed and it did! No more hanging up as I push stock past the second fence face. Very impressed especially since my table is over 2 years old. Thank you Kreg....you rock!
I have the same problem with mine Steve. Not sure what to do about it. I don't want to sand on the other fence face, but it is annoying, not to mention dangerous having the stock stick in the middle of a cut.
Hi Steve. Sorry to hear that you are experiencing issues with your Precision Router Table. Please get in touch with the Kreg Technical Support Team by calling 800-447-8638 or by emailing technicalsupport@kregtool.com. They are very knowledgeable, and will gladly help you troubleshoot these issues. Thanks!
KregRep
Hi Steve , sorry to hear about your problems with your table . I have the Kreg bench top table not had any problems with mine although I think it could do with more of a overhang on all four sides to clamp too when the need arises. Just a thought has the two rods that we use for trueing a board inadvertently been left in behind the second fence? If all seems correct contact the Kreg Rep on this site he is usually very helpful hope this helps Mick!!
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
You need to be a member of Kreg Owners' Community to add comments!
Join Kreg Owners' Community