Kreg Owners' Community

If your Kreg pocket holes are getting harder to drill, or your drill bit gets excessively hot during operation, it may be time to get your drill bit(s) professionally sharpened. Luckily, the professionals at Kreg are here to help you out.

Simply send your drill bit(s) to:
Kreg Tool Company
Attn: Drill-Bit Sharpening Service
201 Campus Drive
Huxley, IA 50124

Please include $4 for the first bit, $2 for each additional bit, and your return address. Your bits will then be professionally sharpened and returned to you.

For more information, please call us at 800-447-8638 or send us a message.

Views: 7431

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by Clive Buckingham on May 10, 2018 at 4:52pm

I was told by the dealer here in Australia that the bits cannot be sharpened. I have to buy a new bit.

Comment by Lefty on October 23, 2017 at 1:11pm
I just used this service and I am very pleased.
Lefty
Comment by Glen S on August 3, 2016 at 3:07pm

Great to know of this service.

Comment by KregRep on October 22, 2015 at 9:02am

David, you will need to pay shipping costs and send your drill bit(s) to the address above. Please also include $4 for the first bit, $2 for each additional bit, and provide your return address. Your bits will then be professionally sharpened and returned to you. If you have any further questions, please call us at 800-447-8638 or send us a message.
Thanks, 
KregRep

Comment by phillip Dare on October 22, 2015 at 2:48am

Could cost a motza from Australia lol.

Comment by KregRep on August 13, 2015 at 9:06am

Joseph, please get in touch with Customer Support directly at 800-447-8638 or customerservice@kregtool.com for more information on the accepted payment types. 
Thanks!
KregRep

Comment by joseph joel on August 12, 2015 at 11:32pm
Im interested in having my bits sharpened, however theres no mention of payment types accepted or not accepted. Any info would be appreciated.
Comment by KregRep on November 19, 2014 at 12:24pm

Andy, I apologize for the confusion. The previous information posted here was outdated. I have updated it to match our website, which is correct. If you wish to have your Kreg drill bit(s) sharpened, please send them to us at the address above. Please include $4 for the first bit, $2 for each additional bit, and your return address. Your bits will then be professionally sharpened and returned to you at no additional cost.
Thanks again for pointing this out.
KregRep

Comment by Andy Harris on November 19, 2014 at 10:49am

Bit confused as your website says it is $4 for sharpening for the first bit but above you say there is only the postage charge.  If I have to pay postage both ways as well, then to be honest it makes it cheaper to buy a replacement off Amazon for $8 like I just have done as mine was getting dull.  

Comment by PJ on September 2, 2014 at 1:48am

Great Service. Thank you very much. I'll take it in to consideration when in need.

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff on Monday.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse on Saturday.

HELP! Older Kreg Precision Router Fence, need parts! 1 Reply

Started by Dan Spaulding in Beginners' Zone. Last reply by Dan Spaulding May 17.

kreg production stop extension 1 Reply

Started by Pat Meeuwissen in Beginners' Zone. Last reply by Brad Martin yesterday.

Layout/Project Setup Table 11 Replies

Started by Todd J Michalec12@gmail.com in Beginners' Zone. Last reply by Brad Martin yesterday.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_