Kreg Owners' Community

January 2013 Product Reviews (5)

Kreg Universal Drawer Slide Mounting Jig & Brackets Review

One of my favorite toys is my Kreg Drawer Slide Jig.  There are actually two jigs that you'll want to use to help you install a drawer.  These two jigs really compliment each other, and make completing drawer installs a snap.  I picked up both jigs from Amazon for a really reasonable…

Continue

Added by Daris R. on January 30, 2013 at 12:30am — 4 Comments

Kreg Rip Cut

I was fortunate enough to receive a Kreg Rip Cut last spring as they were first shipping but didn't begin using it until this fall.  Initially I attempted to attach the Rip Cut to my Worm Drive Mag framing saw.  The base of that saw has a lip that is great for pushing dust out of the way but makes it difficult to attach…

Continue

Added by Kevin Bergstrom on January 29, 2013 at 5:30pm — 12 Comments

Kreg sawdust jig relief

We have found the holes in the three hole block imeed the discharge of sawdust during the final depth of the drill bit. We do a lot of hard wood work which appears to be when this plugging of the discharge holes occures. We were wondering if anyone else has this problem and if a solution would be to lower the relief holes to allow sawdust discharge nearer the base of the block.

Added by James Lindemulder on January 25, 2013 at 12:33pm — 5 Comments

My new Kreg tool box

I received a Kreg tool box for Christmas this year.  I love it.  I now have a place to keep all of my Kreg clamps, extra drill bits, extra driver bits, and even my Kreg tool in the bottom of the tool box.  I love the removable trays for screw in the top of the box and the see thru lid.  I love the way that the top is supported with the legs in the back when you lift the top lid to get to the bottom.  The only way this box could have been better is is the bottom was a little deeper but it's…

Continue

Added by David Niebeling on January 12, 2013 at 7:06pm — 5 Comments

Square Cut is not square

I bought a Square Cut to use with my circular saw.



Just before making the first cut I decided to check the angle, and unfortunately the “right angle” came out not to be exact. At first I became very frustrated and was ready to throw it away on the upper shelve. But, as several cuts had to be made at the…

Continue

Added by Misha on January 11, 2013 at 1:13pm — 10 Comments

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt yesterday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_