"Like Dennis above I have to re-enter my data to get access to the plans (all ready have them so did not create a new account)
Other than having to recreate my account information I do like the new site."
"I picked up a 50", 36" and 24" All In one Contractors clamp/saw guide a few months back from Rockler for 69.99 for all three of them. Then picked up the wide jaws for them on Woodcraft for 9.95 a set. I use them to cut up sheet and…"
"Around here (Austin, Texas) birch plywood can be cheaper or only moderately more expensive than MDF for the same thickness. For instance at the local BB store 18mm MDF (it is called 3/4 but it is 18mm) is about $29.99 and 18mm birch ply is $36.23.…"
"Yes it was done from the Kreg Workbench plan I just used hardwood ply instead of the MDF.
As far as the finish goes the only reason I finished it was so I could learn how to apply the General Finishes Seal-A-Cell Clear on something I did not mind…"
"The finish looks too good, the bench looks like more of a piece of furniture instead of a shop bench. You not afraid of scratches, dents, etc?
Anyways, it really looks good!
Did you use the Kreg Workbench plan? I built 2 of them and made an…"
"I built some very simple but very sturdy garage shelves out of 2x4's and exterior sheeting plywood (nothing fancy here). I have to admit that I really like the way they have came out. And because they are 2x4's I have been hanging other…"
"I've see the Jack Bench before and some of the ideas from that one have been peculating in my head for a while now. Did not know about the one at The Wood Whisperer. Well I should say I watched the video for the construction of the top but have…"
"Not the best pictures but here are the shelves I'm building for my garage. The next one I build will be fully enclosed because I'm going to be puting chemicals in it and I don't want my kids getting into it.
The first one I built was…"
"I'm in the process of cleaning up and organising my garage (actually just started on it) I'm building all the shelving out of 2x4's (main posts and shelve support) and plywood for the actual shelves. Of course I'm using pocket…"
"I understand the desire to save money and make your own plugs but when you factor in the time required to make them yourself I really don't see how you are saving much if any money on them. What I can understand though is making them so that…"
"I did not realise that the Kreg forums was hosted on Ning until just now. It is so easy and inexpensive to host your own forum on your own servers that I just assumed that Kreg hosted there own. Well if kreg does not or is not paying for the premium…"
Hi AllJust got myself a new Metabo mitre saw, kitted it out with a new Freud Pro blade as well as "pimped up" my bench with LED lighting so I can find stuff! I have 22 LED daylight tubes in my fittings in the garage so there is more than enough…Continue
I originally bought Ridgid tools for the warranty, well I had to replace batteries. Very easy and got new batteries and chargers. Found out they don't make 24 volt tools any more, so I sent in a hammer drill, impact driver and light for replacement…Continue
I am going to try and new project. Never made cabinets before. Researched and You-tubed like crazy. So many opinions. Mine are going to be:1 each= 30"W x 14"D x 38"H2 each =29"W x 14"D x 38"H1 floor to ceiling cabinet 18"W x 24"D and the height…Continue
Perhaps this question has already been asked somewhere on this forum but I wasnt able to find it after an hour or so of searching. Is there a recommended length of Kreg screw to use when combining a 1x6 into a 4x4 post. I have seen a few conversion…Continue
I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.