Kreg Owners' Community

Richard Sands
  • Male
  • Portsmouth, NH
  • United States
Share on Facebook

Richard Sands's Discussions

Application to play the Kreg DVDs on the computer
2 Replies

I tried to play three of the Kreg DVDs on my computer using several different applications or programs which play other DVDs, but the Kreg DVDs would not play.  I finally got the Kreg DVDs to play…Continue

Started this discussion. Last reply by Richard Sands Oct 10, 2011.


Richard Sands's Page

Latest Activity

Richard Sands replied to Fins59's discussion 'Table Saws - Be Careful'
"Here's info on Bosch's new GTS1041A REAXX™ Portable Jobsite Table Saw which will be available Fall 2015 according to Bosch's recent Press…"
Mar 30, 2015
Richard Sands replied to Woody Douglas's discussion 'narrow slide out pantry'
"Woody, Are these rollout bins and rollout trays what you're looking…"
Feb 23, 2013
Richard Sands replied to George Stoltz's discussion 'Modification to clamp'
"I haven't tried cushioning yet, but it is a great idea. I have had slight impressions in soft wood when using my Kreg clamps and Kreg jig.   In stores where they sell the round felt pads, with stickem on one side, for chairs legs and…"
Feb 23, 2013
Richard Sands replied to Justin's discussion 'Miter Saw Blade'
"Hi John, I am just a beginner compared to you.   I understand that your 80-Tooth blade will cut smoother than my 60-Tooth will.  From what you wrote, I think that I may have been pushing the saw too quickly.  So that I…"
Oct 19, 2012
Richard Sands replied to Justin's discussion 'Miter Saw Blade'
"I agree with Carlos.  I bought the Freud #LU91R010 60-Tooth blade to make finish-grade cuts with my 10" sliding compund miter saw.  I have used it mainly for cutting soft wood (northern select pine and poplar) and for…"
Oct 18, 2012
Richard Sands replied to Tom's discussion 'Built-in Bookcase & Media Center'
"Tom,  Great work, especially for a first project! Please show us pics of both sides of one of the doors and tell us how you made the doors."
May 26, 2012
Richard Sands replied to KregRep's discussion 'Official Deck Jig™ Thread'
"Does using pocket holes to build exterior stairs meet the latest IRC Residential Building Code?"
May 17, 2012
Richard Sands replied to Gary roofner's discussion 'Deck jig in plastic grooved decking'
"I'm removing and rebuilding a large backdooor landing and the steps down to the ground, about 8' vertical.  I was thinking about buying a Kreg Deck Jig for this project.  I'll be using the pressure-treated lumber…"
May 4, 2012
Richard Sands replied to Pat Meeuwissen's discussion 'How to keep the wood at a true 90'
"I cannot see the business end of the Kreg clamp in the image you posted.  Are you using the Kreg Right Angle Clamp, ITEM # KHC-RAC, shown at ?"
Apr 2, 2012
Richard Sands replied to Reynolds Negrin's discussion 'Beginners Wood Choice'
"What is your first project?  How big is it? Select-grade pine costs the most.  Sometimes, after looking through a number of #2-grade pine boards, I have been able to buy #2 pine boards which only have one knot at one end or along one…"
Mar 28, 2012
Richard Sands replied to Eddie Bivens Jr's discussion 'Edgebanding Pocket Holes'
"I have put a 1-1/4" edgeband on 3/4" plywood shelves using my K4.  Can you post a picture of what you have done?"
Mar 28, 2012
Richard Sands replied to David Morgan's discussion 'Missing parts in new jig?'
"I bought a Kreg Multi-Mark at Lowe's.  It is a fantastic tool and I highly recommend it.  If I were you, I would take it back to Lowe's with my sales receipt, tell them the problem and ask for another one."
Feb 14, 2012
Richard Sands replied to Bob Dahlberg's discussion 'Kreg screw vs biscuits'
"Colonel, I am also new to the Kreg system.  I have found good information in the Kreg K3 Manual.  Kreg is revising it into a K4 Manual but I do not see that online yet.  So, I suggest looking at the Kreg K3 Manual most of which…"
Jan 24, 2012
Richard Sands replied to Greg O'Shea's discussion 'K4 Markings?'
"Hi Greg, What did you use for the nice work in filling in the markings so that they are easier to see? BTW, regarding the markings you asked about, Tom is correct.  That and a few other tips about the Kreg K4 were covered in the Kretg Plus…"
Jan 24, 2012
Richard Sands replied to Jim Taylor's discussion 'Edge Joining Technique'
"Don, Hope that info helps.  Show us the result when it's finished. Richard"
Jan 15, 2012
Richard Sands replied to Anthony Reed's discussion 'How to make a door with insert panels?'
"Mike,   It's hard to believe that the entertainment center is your first major project. Very nice work!  As Steve wrote: it looks like you have been building excellent work for…"
Jan 13, 2012

Profile Information

Which Kreg products do you own?
Kreg Jig® Master System, Micro-Pocket Drill Guide
How would you describe yourself?
Beginning Woodworker

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 


  • Add Videos
  • View All


Cabinet Hardware Jig - Brad Point Bit vs. Regular Twist Bit 1 Reply

Started by Ken Kortch in Other Kreg® Products. Last reply by Brad Martin 6 hours ago.

What hinge should I use? 2 Replies

Started by Lynn Greff in General Woodworking. Last reply by Lynn Greff 5 hours ago.

Kreg cabinet hardware jig

Started by Robert Melrose in Other Kreg® Products Apr 16.

designing your projects on-line 4 Replies

Started by Robert Wolf in Beginners' Zone. Last reply by KregRep on Thursday.

Plugs For 2x4's 4 Replies

Started by Dan Smith in Beginners' Zone. Last reply by Glen S Apr 9.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…


Posted by Glenn Revheim on April 5, 2018 at 5:57am — 1 Comment

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…


Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service