Kreg Owners' Community

KregCS
  • Huxley, IA
  • United States
Share on Facebook
Share

KregCS's Friends

  • Tony
  • Paul Mundy
  • gale
  • Drew Thompson
  • michael evans
  • Derek Gould
  • Ryan McLaughlin
  • John Harrison
  • Glenn Deel
  • Ted Earl
  • Bo M. Wiberg
  • Kevin McCabe
  • Frank Cannon
  • Roberto Caballero
  • Mike Quattrone
 

KregCS's Page

Latest Activity

KregCS replied to Caleb Sanz's discussion 'Using Kreg Jig HD for 4x4s into 4x4's'
"Caleb,  When working with the HD jig you can definitely use it in material larger than 2X.  However, like you have stated it will not have the screw come through the center of your material.  We recommend with material larger than 2X…"
May 9
KregCS replied to Troy Greek's discussion 'Foreman Question'
"Troy,  Due to the torque of the motor, your piece can move slightly once the bit is entering the wood.  This will not affect the drilling of the pocket hole and is considered normal drilling operation.  if you have any other…"
May 5
KregCS replied to Jasper Bouwmeester's discussion 'How durable are Protec-kote screws?'
"Jasper,  Unfortunately our Protec-Kote screws have not been around for more than five years so I would not be able to give you a 100% definitive answer.  The testing we have done shows that you should not have any problems for that span…"
May 3
KregCS replied to Luke Troughton's discussion 'Kreg Kms 8000 track and stop kit'
"Luke,  You can either fasten the fence section from the bottom or if you want you make an L shaped piece so that you can screw that directly to the table top.  I know its not the easiest to screw from the bottom up into a vertical piece…"
May 2
KregCS replied to Luke Troughton's discussion 'Kreg Kms 8000 track and stop kit'
"Luke,  The issue is that every saw is going to have different measurements so its hard to give you an exact plan for your saw.  If you look in the instructions for the KMS8000, on the last page in the bottom left corner there is a sample…"
May 2
KregCS replied to Todd Guill's discussion 'yet another jig/drill setting question for different thickness woods'
"Todd,  When working with two different thicknesses the general rule of thumb is to set everything for the thinner thickness and use the corresponding screw.  For example, in your situation you will want to use the 1/2" settings and…"
Apr 26
KregCS replied to Charlene Christensen's discussion 'Ideas to help hold 2x4 (and thicker) stock when joining'
"Charlene,  Unfortunately when working with larger pieces like this you kind of have to improvise.  I know some people when working with larger pieces have used ratchet straps in order to hold them together while joining.  Some use…"
Apr 25
KregCS replied to Bob Molloy's discussion 'Multipurpose Work Center Parts List'
"Bob,  Sorry for the delay in responding as I was having our Marketing team look this over to double check.  That piece was adding to the plan in error.  We have since corrected this error and a few other we found and the new version…"
Apr 21
KregCS replied to douglas E. Cooper's discussion 'wood splits'
"Douglas,  I was curious if you are using fine threaded screws when you are joining your materials.  If not this could cause your material to split.  If this is not the case it could be in the dryness of the wood itself.  If it…"
Apr 19
KregCS replied to Bob Molloy's discussion 'Multipurpose Work Center Parts List'
"Bob,  I am unsure of the plan you are referring to.  If you could let me know where you found this so I can take a look at it I would be more than happy to assist you.  "
Apr 17
KregCS replied to Jay Glover's discussion 'Router table'
"Jay,  I'm sorry to inform you that we do not have a quick fix for this situation.  However, I know we have had some customers create their own levelers to place in the corners in order to match up with this lift.  Unfortunately…"
Mar 20
KregCS replied to George Bokros's discussion 'Broke off Three Posket Hole Screws'
"George, Depending on the density of wood you are screwing into it can cause additional issues with joining your material. First off I'm assuming that you are using our fine threaded screws since you are working with hardwoods. If this is not…"
Mar 14
KregCS replied to Deac Manross's discussion 'How easy is it to adjust router bit height adjustment with a Kreg Router Table? Can you do it ABOVE the table?'
"Deac,  As long as the router is installed properly onto the plate you should be able to raise the router high enough to use the wrenches to loosen your bit.  If you have any other questions please let us know.  "
Mar 14
KregCS replied to Michael's discussion 'question about kreg foreman and tear out'
"Michael,  I was curious if you could supply me with a picture.  There will always be some tear out due to the way the bit is entering the wood.  If I could see what you are getting I would be able to tell you if this is an acceptable…"
Dec 30, 2016
KregCS left a comment for Anthony Tosi
"Anthony,  You should be able to but it would depend on the condition of the wood used and how the crates are assembled.  If the two pieces are not cut square, it could cause the joint to not pull tight or pull at an angle.  Would you…"
Dec 29, 2016
Anthony Tosi left a comment for KregCS
"Hi KregCS, Wondering if the Kreg Jig would be able to secure 2 pine crates together that Home depot sells, the outer edges only."
Dec 29, 2016

Profile Information

Which Kreg products do you own?
Kreg Jig®, Kreg Jig® Master System, Kreg Jig® Jr., None Yet
How would you describe yourself?
Moderate Woodworker

Comment Wall (16 comments)

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

At 7:47pm on December 28, 2016, Anthony Tosi said…

Hi KregCS, Wondering if the Kreg Jig would be able to secure 2 pine crates together that Home depot sells, the outer edges only.

At 9:06pm on July 16, 2014, Paul Mundy said…
Paul R. Mundy
Cell: 716-480-7787
Email: prm387@gmail.com
At 7:43pm on February 9, 2011, Thaddeus Webster said…
Thanks. That would be fine! Sorry about the late response, but for some reason I didnt get notification of your response. 3117 W. Danbury Dr. Phx, AZ 85053
At 8:39pm on November 11, 2010, Ed Morris said…
The Kreg Shows that are coming your way. Is there any reason that these shows stop at the Canadian/US boarders?
At 6:32pm on November 1, 2010, Randy Popkes said…
Yes that is what I am missing from my kit Randy
At 10:37am on November 1, 2010, Glenn Deel said…
KregCS;

Have You Ever Though About Hooking Up With David Venable On QVC To Sell Your Kreg Jigs? A lot Of People Would Buy Your Items That Do Not Know About Your Jig!! QVC Reaches Out To Millions Of People You Can't, And Don't Reach!!

Yours Truly,
Glenn Deel
glennzona@yahoo.com
At 4:33pm on October 29, 2010, Randy Popkes said…
I have lost the brass locking bolt how can I get a new one
At 7:02pm on August 29, 2010, Thaddeus Webster said…
I wish I would have known before purchasing what I did that the Bench Klamp would not work with the Mini-Trak.I dont think I saw anything in the description stating that. I would have considered buying the larger Trak instead or another accessory in place of the Bench Klamp that would be compatible.
At 6:59pm on August 29, 2010, Thaddeus Webster said…
Oh, and yes. I was referring to the blue support/stop that came with my jig. Thanks!
At 6:40pm on August 25, 2010, Thaddeus Webster said…
Sorry about the ambiguity. The crescents that I was referring to seem to be cuts into the anodized aluminum made by the drill bit or chuck that made the fastening holes in the bottom of the Trak. I can send a pic if you need one. Thanks for your quick response!
 
 
 

Need Help?

Technical Support is always happy to help via phone or email. Call toll-free 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Product Reviews

Kreg Mobile Project Center

Posted by John Tomkinson on May 5, 2017 at 5:34am — 2 Comments

Handy jig to hold and push plugs in!

Posted by Dave Stanton on March 31, 2017 at 5:53pm — 1 Comment

Laguna 14BX Band Saw

Posted by Tim Grace on December 20, 2016 at 1:52am — 1 Comment

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_