Kreg Owners' Community

Deac Manross
  • Male
  • Edinboro, PA
  • United States
Share on Facebook
Share

Deac Manross's Friends

  • KregRep

Deac Manross's Discussions

How easy is it to adjust router bit height adjustment with a Kreg Router Table? Can you do it ABOVE the table?
3 Replies

I have a Porter Cable 690 and 890 series routers.  Is the Kreg table designed at all to be able to adjust the router bit height from ABOVE its router table (at least for the 890 series?) or do you…Continue

Started this discussion. Last reply by Robert Melrose Mar 14, 2017.

 

Deac Manross's Page

Latest Activity

Robert Melrose replied to Deac Manross's discussion 'How easy is it to adjust router bit height adjustment with a Kreg Router Table? Can you do it ABOVE the table?'
"You would have to drill a hole for that. The Kreg router plates don’t have any mounting holes in them. They do have a template that will help you center your router though. Then you mark the screw locations and the location for the height…"
Mar 14, 2017
Deac Manross replied to Deac Manross's discussion 'How easy is it to adjust router bit height adjustment with a Kreg Router Table? Can you do it ABOVE the table?'
"Well, my question was more aimed at the Porter Cable 890 which comes with a shaft/dial that goes  through the router table plate to adjust height.  Would I have to drill a hole in the Kreg router plate to allow that through? Or are there…"
Mar 14, 2017
KregCS replied to Deac Manross's discussion 'How easy is it to adjust router bit height adjustment with a Kreg Router Table? Can you do it ABOVE the table?'
"Deac,  As long as the router is installed properly onto the plate you should be able to raise the router high enough to use the wrenches to loosen your bit.  If you have any other questions please let us know.  "
Mar 14, 2017
Deac Manross posted a discussion

How easy is it to adjust router bit height adjustment. Can you do it ABOVE the table?

I have a Porter Cable 690 and 890 series routers.  Is the Kreg table designed at all to be able to adjust the router bit height from ABOVE its router table (at least for the 890 series?) or do you have to do it all from down under?ThanksSee More
Mar 13, 2017
Deac Manross replied to Mike rignola's discussion 'Kreg Router Table'
"I haven't read anything regarding the Router Table as to how easy/hard it is to adjust your router's bit height once it is installed in the table. Do you have to take the whole thing out? Is there a way (assuming you have the right router)…"
Mar 13, 2017
Deac Manross updated their profile
Dec 23, 2012
Deac Manross is now a member of Kreg Owners' Community
Mar 4, 2010

Profile Information

Which Kreg products do you own?
Kreg Jig®, Kreg Jig® Master System, Kreg Jig® Jr.
How would you describe yourself?
Moderate Woodworker

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff May 20.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

HELP! Older Kreg Precision Router Fence, need parts! 1 Reply

Started by Dan Spaulding in Beginners' Zone. Last reply by Dan Spaulding May 17.

kreg production stop extension 1 Reply

Started by Pat Meeuwissen in Beginners' Zone. Last reply by Brad Martin on Tuesday.

Layout/Project Setup Table 11 Replies

Started by Todd J Michalec12@gmail.com in Beginners' Zone. Last reply by Brad Martin on Tuesday.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_