Kreg Owners' Community

Brian fleming
  • Grove City, OH
  • United States
Share on Facebook
Share

Brian fleming's Discussions

Kreg setting for 3x3
1 Reply

Question i need pocket holes to join my table legs and apron . What setting would I set my kre jig up for a 3x3 I will be using 1 inch thick oak for the apron. And I will beef up the top of it with…Continue

Started this discussion. Last reply by Tim Grace Jan 22, 2017.

Glue
3 Replies

Question I put together a 4x4 foot table with 1 inch red oak barn wood all if it went through a jointer before hand. I used pocket screws only and yes it took a ton of screws and I didn't get glue I…Continue

Started this discussion. Last reply by Glen S Jan 22, 2017.

Card table
5 Replies

Going to be building a card table the table top is 150 year old read oak . The apron is 50-75 year old oak . And I ordered red oak turning stock on line for the legs. My question is when I go to…Continue

Started this discussion. Last reply by Glen S Jan 22, 2017.

New project rustic barnwood bar top
6 Replies

Hello all my name is Brian I'm newer to wood working and loving my Kreg Jig. I do have a question though I put together 1 inch 7 ft. Long pieces of red oak barn wood to put on top of my base…Continue

Started this discussion. Last reply by Brian fleming Jan 17, 2017.

 

Brian fleming's Page

Latest Activity

Tim Grace replied to Brian fleming's discussion 'Kreg setting for 3x3'
"Set the jig to the actual dimension of the wood you are drilling into.   In this case, I would attach the apron to the legs (and top?) using the apron's actual thickness (you state 1", is it actually ¾"? )  The jig…"
Jan 22, 2017
Glen S replied to Brian fleming's discussion 'Card table'
"The aprons & legs are on a vertical plane. Top is on a horizontal plane. Light play off these planes differently. The apron for example will be in the shadows of the overhanging top. Make a quick mock up with some scraps & stain both pieces…"
Jan 22, 2017
Glen S replied to Brian fleming's discussion 'Glue'
"More than likely just the poly Brian. You'll break the top coat finish,, it lays on top of the stain,, when it comes apart. The stain is actually in the wood so you "should" be fine there."
Jan 22, 2017
Brian fleming posted discussions
Jan 21, 2017
Brian fleming replied to Brian fleming's discussion 'Glue'
"Will I have to re sand all the poly and stain off then start over"
Jan 21, 2017
Ken Darga replied to Brian fleming's discussion 'Glue'
"Brian, I's take apart, when the loose joint meets--- remove the old glue--- reglue it and clamp tight. Use cawls to avoid bowing."
Jan 21, 2017
Brian fleming replied to Brian fleming's discussion 'Card table'
"Yea the only reason I'm thinking stain is to match up everything else in the room, but if I did clear it would definitely make everything look uniform ."
Jan 19, 2017
Tim Grace replied to Brian fleming's discussion 'Card table'
"Danish oil, clear shellac, clear poly, etc. I'm not a big fan of stains in things that I do - probably because I can never seem to apply it and have it look like I had envisioned. I also like being able to see the character of the wood,…"
Jan 19, 2017
Brian fleming replied to Brian fleming's discussion 'Card table'
"I would really like to do the top in a dark stain. Would the table not look right if I did the aprons and the legs in just a clear? And by clear do you mean like a Danish oil or something like that ?"
Jan 19, 2017
Tim Grace replied to Brian fleming's discussion 'Card table'
"I would think that they would absorb the stain at a different rate, resulting in darker or lighter coloring between the three.  Is finishing in clear an option?  "
Jan 19, 2017
Brian fleming posted a discussion

Card table

Going to be building a card table the table top is 150 year old read oak . The apron is 50-75 year old oak . And I ordered red oak turning stock on line for the legs. My question is when I go to stain everything are the tints going to be drastically different ?
Jan 18, 2017
Brian fleming posted a photo

Rustic barnwood Bar

120 year old red oak bar
Jan 17, 2017
Brian fleming replied to Brian fleming's discussion 'New project rustic barnwood bar top'
"I'm all done guys and I can't figure out how to post a pic.???"
Jan 17, 2017
Glen S replied to Brian fleming's discussion 'New project rustic barnwood bar top'
"Easy fix. Cut 4 boards as long as the top is wide. Place one set,, these are called cauls,, over/under on each end. Clamp them tight. This will draw the bow out on the ends. Inspect the joint carefully & place more cauls where they are needed.…"
Jan 17, 2017
Don Foley replied to Brian fleming's discussion 'New project rustic barnwood bar top'
"Brian, Since you did not glue the planks together to form the tabletop I suggest removing the bowed piece, drilling new pocket holes and before re-installing it use cauls or some other form of  forcing the bowed board flat.  Then reattach…"
Jan 14, 2017
Brian fleming replied to Brian fleming's discussion 'New project rustic barnwood bar top'
"Thanks Don it is attached with mechanical kreg screws I chose not to glue it . I don't have the capability of using a joiner to have symmetrical edges ."
Jan 13, 2017

Profile Information

Which Kreg products do you own?
K4 Master System
How would you describe yourself?
Beginner DIYer
How did you learn about the Kreg Owners' Community?
kregtool.com
What's one interesting fact about you, your life, your garage, shop, or home?
I'm loving woodworking

Brian fleming's Photos

  • Add Photos
  • View All

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Pneumatic conversion pocket hole 2 Replies

Started by Michael B in Beginners' Zone. Last reply by KregCS on Monday.

Kreg Storage 2 Replies

Started by Jim Mahan in Kreg Jig® Projects. Last reply by R. E. Woods Feb 16.

Old Kreg Jig - K1?

Started by Kent Bruner in Kreg Jig® Purchasing Feb 11.

concealed hinge jig stop collar 1 Reply

Started by Joe Grane in Other Kreg® Products. Last reply by KregRep Feb 12.

Kreg Jig K3 defect or not? 5 Replies

Started by Igor in Kreg Jig® Purchasing. Last reply by Randy Hills Feb 13.

Product Reviews

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_