Kreg Owners' Community

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by Jim Delorme on November 16, 2011 at 10:44am

Your very welcome...

Comment by Evan Siefke on November 15, 2011 at 11:34am

Hello Jim, I loved your jig idea so much I had to incorporate it into my new mobile assembly/Router table I am building. Thanks for the help.

 

 

Comment by Paul M Cohen on October 8, 2011 at 3:56am

I have been traveling, the two pictures below show the jig and track. The T-Nuts are visible in the second picture and it a bracket used to hold a 4" dust colletion host that. If I do not clamp the hose the suction pulls it loose when I turn on the collector.

 

The hose holder is screwed into on of the T-Nuts. Since my bench is next to all wall I need to move the jig between two locations to hold long pieces. Also notice the Kreg Stops that can be moved along the track. The top picture is to the right of the bottom picture.

Comment by Peter Lopez on October 7, 2011 at 8:33am

Great job Jim!!!

 

Good Idea, why don't you post a couple of Pics Paul?

Comment by Paul M Cohen on October 7, 2011 at 12:51am
I did something a little different I sunk T-Nuts all along the edge of my bench positioned so I can mount 2 ft sections of T-Track separared by the spacing for the Kreg Jig. In each gap I put in four T-Nuts spaced so they would hold the Kreg Jig in place. On the T-Track I mounted two Kreg Stops (one came with the jig). Now I can position the stops so they are about 8" away from the center of the Kreg Jig. With the setup I can quickly drill two holes near the board ends and two 6-8" closer to the center. For most of my work 4 holes per side is enough. This allows me to drill all the holes to assemble production pedestals very quickly. When I am done drilling all the holes a few screws removed with a power screwdriver and I am ready to use the bench for assembly.
Comment by George K. Walker on October 22, 2010 at 3:09pm
I'm looking forward to receiving my catalog so I can order clamps, screwe, "etc" to enable me to start a couple of projects, the little bet of stuff received with origional Kreg order is gone.
Patient waiting
George Walker
Comment by montoya genaro on October 21, 2010 at 2:54pm
great idea i like the workbench
Comment by Eric Rusch Sr on October 21, 2010 at 10:30am
That slide out is a great idea.
A dedicated Kreg station would make using this joinery method more likely.
Thanks for sharing.
Comment by Sleddogdad on September 23, 2010 at 10:50pm
Love the slide out!

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Cabinet Hardware Jig - Brad Point Bit vs. Regular Twist Bit 1 Reply

Started by Ken Kortch in Other Kreg® Products. Last reply by Brad Martin yesterday.

What hinge should I use? 2 Replies

Started by Lynn Greff in General Woodworking. Last reply by Lynn Greff yesterday.

Kreg cabinet hardware jig

Started by Robert Melrose in Other Kreg® Products Apr 16.

designing your projects on-line 4 Replies

Started by Robert Wolf in Beginners' Zone. Last reply by KregRep on Thursday.

Plugs For 2x4's 4 Replies

Started by Dan Smith in Beginners' Zone. Last reply by Glen S Apr 9.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 1 Comment

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_