Kreg Owners' Community

Rating:
  • Currently 0/5 stars.

Views: 277

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by michael evans on November 28, 2015 at 3:17pm

Thanks for taking the time to reply John, never seen the like of the blade runner before so i was curious. It sounds like your a fan of this saw ,here in the U.K not so much choice with tools like this .Go steady Mick.

Comment by John Tomkinson on November 28, 2015 at 10:23am

Always happy to share info with my fellow Kreg Members....Regards, Michael, from Western Canada!  John.  Michael, this is a photo of my original Bladerunner sitting on its Wall Mount attachment.  And the cedar wall sections were all cut with this unit.....it did a beautiful job!

Comment by John Tomkinson on November 28, 2015 at 10:17am

Hi, Michael.  Yes, this Rockwell Bladerunner X2 uses T-shank blades and comes with 5 different styles of blades that can cut through metal, PVC, plastic, tile, etc.  Please look at the photos I posted, and you will see where I used my Kreg HD Pocket Holes to assemble many of the wood sections in my carport/workshop upgrade.  Check out YouTube videos to see the Rockwell Bladerunner.  The original Bladerunner [which I also have] had an arm support, off to the right of its table, which restricted the width of wood your wished to cut.  The newer version, the Bladerunner X2 has eliminated that side arm, and you can do rip cuts straight on thru....the space made with your cutting blade is enough to slide your cutting sections thru the narrow upright support at the rear of its table.  These are wonderful units for the DIY'er, because they can even cut your 2x4s [1.5 inches], and you can use other T-shank blades besides just the Rockwell ones, ie:  Bosch, etc.  You can use its Scroll blade to make scroll cuts, although not perhaps as 'perfect' as a dedicated Scroll Saw.  The beauty of this handy little unit is that it frees up both of your hands to control the piece you wish to cut.  You can also get a wall attachment if you don't have a bench access.  Hope this helps with your question, Michael.  Happy Kreg-ing!  John

Comment by michael evans on November 28, 2015 at 4:29am

Hi John is that a scroll saw?

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Pneumatic conversion pocket hole 2 Replies

Started by Michael B in Beginners' Zone. Last reply by KregCS on Monday.

Kreg Storage 2 Replies

Started by Jim Mahan in Kreg Jig® Projects. Last reply by R. E. Woods on Friday.

Old Kreg Jig - K1?

Started by Kent Bruner in Kreg Jig® Purchasing Feb 11.

concealed hinge jig stop collar 1 Reply

Started by Joe Grane in Other Kreg® Products. Last reply by KregRep Feb 12.

Kreg Jig K3 defect or not? 5 Replies

Started by Igor in Kreg Jig® Purchasing. Last reply by Randy Hills Feb 13.

Product Reviews

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_