Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
Chat not workingit says there are 11 online in the chat, but when I open the chat, it only shows me, and when i post something to it, it doesnt show up. Is… Started by Mike Kahle in Kreg Jig® Purchasing |
1 |
Apr 9, 2011 Reply by Mike Kahle |
Post photos of your shop!Big, small, full of tools, or just starting... post photos of your shop! I'm sure there's quite a wide range of them out there.. I used to… Started by Bob Farmer in Miscellaneous |
31 |
Apr 5, 2011 Reply by John Harrison |
Dorm Furniture IdeasI have been approached by my son and his roommates to build furniture for their first apartment. These guys have basic needs - place for… Started by Rene' Martinez in Kreg Jig® Purchasing |
1 |
Apr 4, 2011 Reply by David Dean |
Bookcase Headboard and Mattress PlatformCompleted my first real project using Kreg joints and can't wait to get to my next project which will be a credenza. I learned A LOT while… Started by Eric Laeyendecker in Kreg Jig® Projects |
0 | Apr 3, 2011 |
ScrewsI am attaching skirts to table legs, and the skirts are one inch thick pine. I know I am supposed to use the coarse thread, but what is the… Started by Michael Hobert Edwards in Kreg Jig® Operation |
2 |
Apr 3, 2011 Reply by Michael Hobert Edwards |
Bench Drill PressOccassionally I have to drll holes for dowels etc requiring great precison and portable battery powered drills do not do the job no matter… Started by Ash Parikh in Kreg Jig® Purchasing |
11 |
Apr 2, 2011 Reply by Ash Parikh |
Fly tying desk?Hi everyone, I'm wondering if there are any other fishermen out there who may have built a fly tying desk. In case you don't know what tha… Started by Bob Bainbridge in Community-Specific |
4 |
Mar 30, 2011 Reply by jigman |
Foto ?Dave Horn here, I've followed the prompt to post a foto and jpeg comes up but foto don't come out. What did I do wrong or not do right? H… Started by Dave Horn in Community-Specific |
0 | Mar 30, 2011 |
Can you use pocket holes on beveled cuts?I'm new to woodworking and I just purchased a miter saw. I've been making different cuts just to get use to the saw and I was wondering, i… Started by Bryan in Kreg Jig® Operation |
1 |
Mar 30, 2011 Reply by WTH |
trouble with a mitered returnAlright I am trimming around some copper sheeting that I installed as a heat reflector for a wood stove, as shown in the picture below. Aft… Started by WTH in Kreg Jig® Operation |
6 |
Mar 30, 2011 Reply by WTH |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service